Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
ShaunCorbs's latest activity
-
ShaunCorbs replied to the thread Toilet waste small drip leak - plumbers mait not working.Denso tape -
ShaunCorbs reacted to Barnjet's post in the thread Mixer tap ring sheared during seal replacement - how remove with
Like.
Update: Perrin and Rowe have supplied a complete tap replacement FOC under the manufacturer’s 25 year warranty. Excellent customer service from a great company. -
ShaunCorbs replied to the thread Heat Group Magnaclean copy. Parts of it are excellent..The old adey ones had the same problems the threads would break down / jump due to the plastic being weak on the thread pitch / type of thread
-
ShaunCorbs replied to the thread Megaflo UVC - Very Loud Noise When Hot Tap Opened.Or the diaphragm banging around
-
ShaunCorbs replied to the thread Megaflo UVC - Very Loud Noise When Hot Tap Opened.Well that’s strange as they’ve supplied me one recently I would push more and state there liable for showers and taps as there blocking up also you shouldn’t drink the tap water
-
ShaunCorbs replied to the thread Megaflo UVC - Very Loud Noise When Hot Tap Opened.They would normally supply you with a brand new cylinder as when it degrades it breaks off and can clog stuff so defo shouldn’t be used once identified
-
ShaunCorbs replied to the thread Silent Running Toilet eluding capture.Is the base plastic smooth eg where the silicon / rubber seal mates ?
-
ShaunCorbs replied to the thread Megaflo UVC - Very Loud Noise When Hot Tap Opened.Internal baffle
-
ShaunCorbs replied to the thread Isolation valve with double check valve.The ones I use haven’t had a problem but it’s like anything needs to be used / operated 6 monthly etc
-
ShaunCorbs replied to the thread PRV with Gauge Question.Correct if you look at the brass stop tap eg top on flow will be to the left when it should be going to the right
-
ShaunCorbs replied to the thread Isolation valve with double check valve.Filling loop
-
ShaunCorbs replied to the thread Isolation valve with double check valve.Yep I fit the metal handle ones from monster plumb
-
ShaunCorbs replied to the thread PRV with Gauge Question.The brass Stop tap is the wrong way round Sounds like it’s operating like it should Set pressure 2 bar 4 bar static
-
ShaunCorbs replied to the thread Viva full valve double check valve.That was in 2021 so maybe still there or updated design ?
-
-
ShaunCorbs replied to the thread What we all working on this week ?.Facebook £50
-
ShaunCorbs replied to the thread Washing machine drain hose..Might be an air gap built in to the washing machine hence the sealed end into the pipe etc First picture is fine
-
ShaunCorbs replied to the thread Shower elbow wall plate..Yes trim down the brass 1/2 thread to match your build up afterwards eg normally make sure the female iron fitting is flush on the front with the plasterboard etc
-
ShaunCorbs replied to the thread Re Condensing boiler.Ideally need an aav on the boiler pipe as the gurgling you hear is a vacuum sucking the water out of the boiler trap Or the boiler condense piping in different
-
ShaunCorbs replied to the thread What do you think of this flexible gas hob connector?.So has copper tube Too many fittings to convert to each end eg hob end you would need a bent female iron and the supplied cooker elbow so 3 joints that end
-
ShaunCorbs replied to the thread What do you think of this flexible gas hob connector?.No just use a bit of 10mm
-
ShaunCorbs replied to the thread Any tips for a non plumber with no pilot light.Pump on / running ?
-
ShaunCorbs replied to the thread Any tips for a non plumber with no pilot light.Does the pilot light at all with both buttons pressed eg gas valve button and ignition ? You have gas don’t you eg pre pay meter ?
-
ShaunCorbs replied to the thread Hive thermostat multizone help.You will need two eg one system pack eg for hot water and one zone eg screwfix code 246JK Then a single zone pack for the remaining zone eg screwfix code 673JK
-
ShaunCorbs replied to the thread Not much water from shower head but high pressure in tap.Yes same some call high flow some big bore etc
-
ShaunCorbs replied to the thread F&e tank vent pipe pouring hot water.Could be a few things eg feed and vent tees in the wrong place, pump too strong, pump weak and boiling over, system blocked
-
ShaunCorbs replied to the thread Not much water from shower head but high pressure in tap.Have you tried high flow shower hoses ?
-
ShaunCorbs replied to the thread Inline potable expansion valves.https://www.pumpsukltd.com/reflex-flowjet-3-4-inch-flow-through-valve.html
-
ShaunCorbs replied to the thread Advice on a Drayton EB valve body leaking from the top.Replace the seal if it looks like one in the link ? https://www.draytoncontrols.co.uk/product/drayton-balancing-key-and-gland-seal-pack
-
ShaunCorbs replied to the thread Inline potable expansion valves.Yes flow through valve not cheap around £100 for a 3/4 one
-
ShaunCorbs replied to the thread Mixer tap ring sheared during seal replacement - how remove.New tap as you haven’t got the snapped part as a spare eg new spout
