Help - changing wireless thermostat

L

landlordray

Messages

34

• Nov 4, 2019

• #1

I recently posted on here as I was having problems with my wireless thermostat and receiver, turns out the receiver has developed a fault.

I have decided to change the old set up for a new receiver and wireless thermostat.

However the wiring set up is different on the new unit ( a Honeywell/Center unit EHE0200361 ) the old unit is a Salus ST620RF
Boiler is Worcester Greenstar CDI

Could anyone help me with the wiring please.

I have attached photos of the old and new receivers.

many thanks

 

Attachments

• 
  IMG_20191104_110452.jpg

  85.1 KB · Views: 32
• 
  IMG_20191104_113515.jpg

  59.7 KB · Views: 26
• 
  IMG_20191104_113549.jpg

  66.6 KB · Views: 27

ShaunCorbs

Super Moderator

Staff member

S. Mod

Plumber

Gas Engineer

Subscribed

Messages

34,632

Solutions

1

• Nov 4, 2019

• #2

Blue to n
Brown to l
Earths together in a chock block
Black to a (this should be into the com port on the old)
White to b

That’s a bit of a guess as can’t make out the writing

 

L

landlordray

Messages

34

• Nov 4, 2019

• #3

Thanks Shaun,

Do I need to link both the ' L ' terminals together on the new Center box ?

Which writing can you not make out - I will take another photo to clarify if this would help

many thanks

 

ShaunCorbs

Super Moderator

Staff member

S. Mod

Plumber

Gas Engineer

Subscribed

Messages

34,632

Solutions

1

• Nov 4, 2019

• #4

landlordray said:

Thanks Shaun,

Do I need to link both the ' L ' terminals together on the new Center box ?

Which writing can you not make out - I will take another photo to clarify if this would help

many thanks

Click to expand...

No just put the wires on the left L

And the back wire there should be writing below the terminal block

 

L

landlordray

Messages

34

• Nov 4, 2019

• #5

Thanks for that.

The writing on the Salus connector block reading left to right is

COM NO Earth Live Neutral

regards

 

ShaunCorbs

Super Moderator

Staff member

S. Mod

Plumber

Gas Engineer

Subscribed

Messages

34,632

Solutions

1

• Nov 4, 2019

• #6

landlordray said:

Thanks for that.

The writing on the Salus connector block reading left to right is

COM NO Earth Live Neutral

regards

Click to expand...

My info then is correct

 

L

landlordray

Messages

34

• Nov 4, 2019

• #7

Thank you. Much appreciated

 

G

garygvl

Esteemed

Gas Engineer

Messages

215

• Nov 5, 2019

• #8

landlordray said:

Thank you. Much appreciated

Click to expand...

you may find youll struggle to get the two cables into the honeywell as you need two neutrals and two lives which look 1.5 maybe 2.5mm. one drawback with this receiver is very small wiring terminals. black and grey no problem as one cable per terminal. the two browns can go one each into the live terminals, the right hand live is just a common live youd use to link to terminal A if you were not doing no volt switching. just be careful with the two blues into one terminal dont have too much bare cable showing on the neutral and live terminals closest together very easy to short out

 

Last edited: Nov 5, 2019

L

landlordray

Messages

34

• Nov 5, 2019

• #9

Thanks for the info, that is really helpful.
I will bear this in mind when I fit the new relay box

thanks

 

L

landlordray

Messages

34

• Nov 7, 2019

• #10

Just an update.

Fitted the new wireless thermostat and receiver a couple of days ago and everything is working a treat

 

ShaunCorbs

Super Moderator

Staff member

S. Mod

Plumber

Gas Engineer

Subscribed

Messages

34,632

Solutions

1

• Nov 7, 2019

• #11

Great thanks for the update