plastic

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

plastic

Recent contents Top users
  1. N

    Fitting ABS pipe

    Anyone worked with this plastic pressurised pipe much? This week was my first and i thought after my years of experience that these stressful days were mostly behind me...alas they are not. Ordered up the stuff in preparation for the job, informed the entire building that the water would be off...
  2. M

    Plastic flow/return into boiler case normal?

    Hi I was viewing a house today and came across a few questionable plumbing practices. Looking at the outside oil boiler I noticed pushfit plastic flow/return going into the case and wanted to know others opinion on this? I would of thought building regulations required copper from the boiler...
  3. G

    Scotland, plastic pipe?

    Scotland i have been told that plastic pipe is not permitted for runs through ceiling, with drops to radiators? does it have to be copper? i am based in England, but working on design for project in Scotland. Thanks.
  4. P

    Heating oil tank (plastic) has rusty coloured layer on bottom...

    Hi The tank is around 7 years old. Any ideas what causes it and/or whether it is a problem? Sorry the photo is not great, it's the best I can get through the small opening. Many thanks
  5. C

    Best way to connect 10mm plastic pipe to 8mm micro bore

    Hi all fitting new radiators and need to connect to 8mm micro bore copper pipe under floorboards, (full rework of pipes not an option) would 15mm plastic pipe be okay or just go up to 10mm plastic pipe ? Also best way to connect , compression or push fit ? Using inserts off course , additionally...
  6. R

    Plastic section on gas pipe entering property...

    Hi everyone, I've recently moved into a new property and had a lot of interference on our TV and Audio equipment, following advice I had our earth changed from PME to 8ft rod and it improved a lot but is still not perfect (the theory is the big factory located near our property is putting...
  7. S

    Dripping hot water bath taps that has a plastic cover over the 1/4 turn cartridge.

    I have a dripping hot water bath tap. I have removed the top but underneath is a plastic cap ( see picture) but the cap will not come off to get to the cartridge, and I don't want to force it in case it breaks. Anybody any ideas on how to remove it, and if it breaks where you would be able to...
  8. T

    How Robust is Solvent Weld Plastic Pipe

    Hi, I ask this question following a little DIY job to clear out my bathroom sink traps. Having got a slow draining sink I unscrewed the two connections (one to sink and one down to waste) and remove the trap and cleaned everything out as best I could. Everything seems to have gone back...
  9. J

    How do I remove the copper pipe from the plastic connector?

  10. C

    Pressure reducer/regulator for plastic water line?

    Good evening, Wondering if i could get a little guidance, I have a 3/8 plastic line running from a softener to a coffee machine (because laziness), however the line pressure seems to be maybe 2.5 bar. The manufacturer state the max line pressure is 2 bar (29 PSI). for the life of me i cant...
  11. S

    tanking. Is it ok to just seal everything with plastic.

    Hi All, I am looking to take my bath out and fit a shower. Regards to tanking. Is it ok to just seal everything with plastic rather than just paint tanking slurry? Thanks in anticipation, best regards Staggers
  12. W

    Plastic bathroom sink?

    I removed the old vanity unit in my bathroom, intending to do a makeover. Finished the shower cubicle, and starting on the vanity. I bought a 2nd hand basin with taps, but I find it's far too heavy to mount on the new counter I made. What I'd like is a plastic basin. I see a few on eeb ay, but...
  13. J

    Pricing whole house in coppers vs plastic

    Gents, It finally happened. A developer has asked for a price for the entire house to be fitted in copper with press fitting...... Does anyone have a rough idea of how much it would cost compared to plastic? Part of me wants to say double but it could be more when factioring labourt and...
  14. M

    Clay to 110mm plastic soil pipe fitting

    Has anyone seen this fitting before clay to 110mm plastic
    • Matt0029
    • Thread
    • fitting pipe plastic soil soil pipe
    • Replies: 9
    • Forum: Boilers
  15. D

    Need to replace plastic trim on shower track

    Hello, I fitted a Cooke and Lewis shower cubicle about 5-6 years ago. The weight of the glass shower door has put large impressions of the roller wheels in the plastic track the rollers run on. Got worse over the years and now it is quite difficult to open and close the shower door. I took some...
  16. J

    Blockages in 10mm plastic central heating pipes

    Our house was built in 2007 and we are the second family to live here - moving in in 2017. The central heating has been working fine - although the gas boiler is perhaps nearing the end of its life. But the boiler is not our current issue. Last winter two of the radiators did not heat up and...
  17. D

    repair small hole in plastic waste pipe.

    small hole in plastic waste pipe which is the better fix ? Hi there need some advice please, i have drilled a small hole in the plastic waste pipe which serves the sink & shower in the loft when doing some work in the toilet underneath on the ceiling i have cut away the plasterboard to reveal...
  18. N

    110mm plastic pipe fitting toilet solvent

    Hiya, my toilet has 110 pipe going to master boss fitting. It's not glued and loose. I think as it's going to master boss that's why it's never glued. It has one drop of water leak after every flush. What I can use to stop leak at same time in utue if It needs to be removed it can be removed...
    • nadeem
    • Thread
    • fitting pipe plastic toilet
    • Replies: 1
    • Forum: Boilers
  19. O

    brass, stainless, or EP/plastic for Well service line fittings

    Where the black polyethelene service line enters this particular structure is by far the most freeze-prone area. The structure is an elevated "mini house" with an insulated, heat-taped plenum taking the poly from below frost line up into the space between floor joists. But, power outages...
  20. L

    Internal plastic pipes

    Hello Please could I have some advice. I recently had an new air source pump and hot water tank system installed. The pipes to the radiators are copper. However, there is plastic pipes to the taps for hot and cold water. I have found a leak in the connection of a plastic pipe. First...
Back
Top