Advice on replacing Central Heating Room Thermostat | Central Heating Forum | Plumbers Forums
  • Welcome to PlumbersTalk.net

    Welcome to Plumbers' Talk | The new domain for UKPF / Plumbers Forums. Login with your existing details they should all work fine. Please checkout the PT Updates Forum

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

American Visitor?

Hey friend, we're detecting that you're an American visitor and want to thank you for coming to PlumbersTalk.net - Here is a link to the American Plumbing Forum. Though if you post in any other forum from your computer / phone it'll be marked with a little american flag so that other users can help from your neck of the woods. We hope this helps. And thanks once again.

Discuss Advice on replacing Central Heating Room Thermostat in the Central Heating Forum area at Plumbers Forums

Status
Not open for further replies.
S

Solorize

Hi,

I would like to replace my existing manual room thermostat which is a “Danfoss Randal RMT 230”,
but could do with a bit of advice.

Due to the current location of the existing unit, tight up against my sitting room door! I could do with
a bit of advice on which model I should replace it with and which would work with the current wiring
(which is shown in the images below).

Due to the location, as said above, is next to a door and in close proximity to my TV unit,
would I be better to go for a wireless unit? (price dependent).

I would preferably like to go for a electronic 7 Day programmable room thermostat.
Also, the hole in the wall that the existing unit fixes badly into, is 80 x 80mm so would the new unit
would need to cover this up, but still be able to fix onto the wall, I may have to turn the new one
90 degrees (i.e. mount it vertically) so that it can cover up the hole.

Please note I will be attempting to install the unit myself, so needs to be simple =)

Also is there anything else I will need to look out for i.e. matching voltages etc..? and would my
type/make of boiler make any difference in which one I should go for?

FYI.
My boiler is: Glow-worm Ultimate 50 FF Non-Condensing Gas Conventional (Regular) boiler

I would be willing to spend approx £100 max on the new unit.

Any advice would be greatly appreciated.

Images of current unit:

Current wiring
Danfoss Randall_RMT_current wiring in box.jpg


Wiring diagram
Danfoss Randall_RMT 230_wiring diagram.jpg


overview of location
Danfoss Randal_RMT 230_overview.jpg

Boiler
boiler.jpg
 
Last edited by a moderator:
Hi,

Thanks for your reply.

I am swaying towards the Honeywell 727.

Someone else i've been speaking to has recommended this as I will be able to have the thermostat
located in a different position.
 
i would not go wireless sick of changing batteries.i moved mine when i was about to decorate.
 
lol, why is that? I have fitted quite a few and never had any problems, yes that are cheap and abit nasty but they have always done that job.
 
Go the Honeywell route either fixed (CM907), or the CM927 Wireless.
I've fitted both, for myself CM907 (Incidentally within you're Budget) and the Wireless for my daughter; who had no existing thermostat
fitted to her system.
Both straightforward from the Honeywell instructions and Boiler Info Manuals.

PS: Boiler Info and Honeywell Manuals available on line
 
These digi stats seem to go wrong all the time, does anyone know of a reliable one. Seem to replace the Drayton receivers a lot.
Can't beat a 240v stat IMO it just needs to be in the right position.
 
See this posting from another thread based on our in-warranty returns. It surprised me.


Ray Stafford said:
Its a good point about RF controls.

I just looked up our return rates - we sell 1000s of RF controls, so our in-warranty return data should give a good feel for reliability.

Return rate on Drayton RF products - 2.03%
Return rate on Honeywell RF products - 2.19%

Here's the one that surprised me:

Return rate on Salus RF products - 2.8%. I would have expected a bigger gap between the "budget brand" and the quality boys.

For comparison, the return rate on hard-wired products is usually 1% plus or minus 0.2%.



 
Status
Not open for further replies.

Similar plumbing topics

I have a home with an oil boiler in a garage...
Replies
0
Views
637
Its a Combi. Its a Worcester Bosch Greenstar...
Replies
8
Views
1K
Hi Basher, Thank you for the reply. So the...
Replies
8
Views
796
Programmable room stat. Probably give you 6...
Replies
4
Views
948
Back
Top