Gas hob on Flexy !!!

[royston]

Some one i know had a boiler fixed over christmas by a gas engineer.And to cut a long story short about wanting a new gas hob and electric oven not going back far enough, the gas man said you are allowed to fit a flexy onto gas hob to get the pipe back to wall far enough for oven to fit.
Now being in the process of completing my gas exams im sure you are not allowed to do this and it has to be rigid copper pipework to hob with a gas tap on, im i right or misunderstood ?

 

[tipintim]

You are correct.

 

[Bartdude]

I went to a job that reported a gas leak last year. Fixed the leak,noticed their gas hob was connected with a flexi.Must be connected with rigid pipework. If you think about it most gas hobs are above ovens which vent heat onto the hob pipework.Not the best place for a rubber hose!

 

[smillsey]

Oh dear,

only allowed rigid pipework on any fixed appliance.

Only flueless appliances which have to be moved out for fitting/maintenance etc are allowed a flexi.

Ie a stand alone cooker.

 

[royston]

Yeah exactly the reasons i thought were correct. Im glad to see that my memory is still holding onto information !!

 

[tipintim]

Your on the ball mate. Costs nothing to ask. Competant you are.

 

[MickBrown]

I lived in Italy for a few years, our gas hob was connected by a rubber tube with jubilee clips. The tube was gas approved and this was a standard way of fitting them.

 

[kirkgas]

by flexi do you mean a braided "plumbing" flexi? if so you are all correct, if by flexi you mean a bayonet fitting and hose, they are allowed unless the manufacturer expressely says must be fitted with rigid pipework, however a bayonet hose has a heat limit of about 70 degrees C so if it is behind an electric oven care needs to be taken to ensure the position of the hose isnt subjected to heat above this, however because im saying it is ok in some situations thats not to say i agree, it is laziness of the highest order, and a properly fitted copper supply means the oven fits in no problem, i used to do loads of kitchens as homers and we used to go on a friday night and strip everything out, on checking the MI for the hob and if it was allowed i would rig up the new hob onto a frame and use the cooker hose and bayonet to connect it to leave them the use of the hob overnight, temp work like that i was happy with but never agree it is a finished job,

 

[gbgas001]

Kirkgas is spot on... the regs state that flued appliances must have rigid pipework. not flueless.

gb-gas

 

[royston]

Im not sure if he had been told rubber or braided as he just told me flexy. Think i will when qualified pipe hobs in rigid copper, seems safer to me.

 

[tipintim]

You know what your talking about.
Free standing cookers, dual fuel, can be connected via flexable pipe with a self sealing bayonet. BS 669
Reasons for this, are to be able to clean behind the appliance and maintenance
Hobs need to be fitted with ridged pipework because they are fitted

 

[kirkgas]

You know what your talking about.
Free standing cookers, dual fuel, can be connected via flexable pipe with a self sealing bayonet. BS 669
Reasons for this, are to be able to clean behind the appliance and maintenance
Hobs need to be fitted with ridged pipework because they are fitted

you need to be careful to seperate your opinion from the Gas Regs, and/or MI and relevant BS docs, you are wrong to make a generic statement like this, AFTER referring to specific MI you can say a specific model cannot be connected by a hose,

 

[tipintim]

Noteded your comment. The above post was not my opinion ,its in the book.

 

[princegoose]

what about semi rigid?

 

[GQuigley67]

what about fanned electrical cookers ?

 

[princegoose]

Sure ive seen this reg in BS but quick google search shows this.

Moffat GAS HOB
MGH 620

Gas Connection

Connection to the gas supply should be with
either rigid or semi-rigid pipe, i.e. steel or
copper.

That Means TacPipe right? Im sure OP means Flexi hose but just thought Id throw it in

 

[metaldust9]

thought it was only cookers and stuff like barbaques,tumble dryers were allowed on flexis ie leisure points cos there removable everything has to be rigid pipework

it says in the viper book gas cookers p-7under hobs it is normal practice to install this type of appliance on a rigid connection unless the mi clearly stats otherwise and incoraprates an isolation valve and a means of disconection

 

[Bartdude]

Only a muppet would would connect a gas hob with a flexible fitting,Regs or no Regs

 

[GASMAN10]

Just wondering, where a hob has been fitted with a cooker hose in good condition, would you AR or ID the hob, if you were just inspecting it.

Thanks

 

[kirkgas]

Noteded your comment. The above post was not my opinion ,its in the book.
gfys

apologies if i am wrong, but having looked through BS6891, and BS6172 and my training books many times i stand by what i posted, but am always willing to learn from someone who knows better, so please advise where it shows in "the book" that EVERY hob MUST be rigid piped

 

[tamz]

what about semi rigid?

You can get wee blue tablets for this nowadays

YouTube - dog ****** commercial (very funny)

 

[kirkgas]

Just wondering, where a hob has been fitted with a cooker hose in good condition, would you AR or ID the hob, if you were just inspecting it.

Thanks

it would depend on the situation, if it was behind an electric hob i would AR as i cannot confirm the surface temp of the back of the oven, or if it was behind a set of drawers and scuffed i would AR it, if it was behind a gas oven, (which is connected by a hose for ease of fitting, therefore back panel surface temp will be low) i would note it as possibly NCS (if i cannot confirm by not having hob MI) if connected by a hose inside a cupboard with nothing near it to damage it then again NCS if no MI,

 

[kirkgas]

Sure ive seen this reg in BS but quick google search shows this.

Moffat GAS HOB
MGH 620

Gas Connection

Connection to the gas supply should be with
either rigid or semi-rigid pipe, i.e. steel or
copper.

That Means TacPipe right? Im sure OP means Flexi hose but just thought Id throw it in

as i posted earlier you are quoting a specific MI which excludes it, we are talking whether is is a generic requirement that EVERY hob MUST be connected with rigid pipe

 

[Puddle]

Thought that if the hob was installed securly in a mobile unit,ie a worktop built on frame with lockable wheels to allow to be moved for cleaning purposes,you were alloowed to fit with flexible hose,however the hose must remain visible and not odscured

Thought it was only ridged appliances that required ridged pipework and it is possible to make a hob as mobile as a cooker

 

[GrahamM]

Backing up kirkgas, as per BS6172:

"Unless stated otherwise in the MI's, a hob shall be connected by a rigid
connection."

As we all know or should know. The Manufacturer is the expert and if they say it can be done or must be done this way then that is the way it goes.