Help! I need a partial bath tap replacement | UK Plumbers Forums | Plumbers Forums
Guest viewing is limited

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Discuss Help! I need a partial bath tap replacement in the UK Plumbers Forums area at Plumbers Forums

Messages
7
Hello,

First of all please excuse my limited knowledge on plumbing!
so my bath tap has started dripping from the ceramic cartridge, It is a single lever bath/shower mixer tap. (See photo)
I have replaced the mixer cartridge with a new one but the sealing face for the cartridge is corroded and I believe is not creating a good seal, hence the drip.
I want to replace the tap but due to the position of it, I would have to remove the entire bath to access the upright spouts.
My question is, can I replace the part of the tap connected to the spouts and if so can any one recommend a suitable replacement?
The gap between the spouts is 150mm.
If you need any more info, please ask as I want to make the correct purchase first time.
Many thanks

Leo
 

Attachments

  • 919C811C-87AC-48FA-996F-6CE92BFE7887.jpeg
    919C811C-87AC-48FA-996F-6CE92BFE7887.jpeg
    120 KB · Views: 38
  • 3BB90255-ACC0-4126-8674-2016D6E929A4.jpeg
    3BB90255-ACC0-4126-8674-2016D6E929A4.jpeg
    107.4 KB · Views: 36
You could leave the tails/spouts in the bath and renew the top part. What size looking down on your tap are the centre to centre of the tap/spouts at the back? Is there a makers name on the tap? Do you have a combi boiler or just gravity hot water?
 
Last edited:
You could leave the tails/spouts in the bath and renew the top part. What size looking down on your tap are the centre to centre of the tap/spouts at the back? Is there a makers name on the tap? Do you have a combi boiler or just gravity hot water?
Bit hard to measure centre to centre at the back because they are oval shaped but sum where between 180-185mm (thats between the spouts mating with the bath). Between the spouts connecting to the tap is 150mm. Unfortunately no markings on the tap for identification and I have a combi boiler.
Many thanks
 
Like this measurement bottom image. If that is the same you could have a thermostatic bath shower mixer or a tap that connects the same as yours.
 

Attachments

  • grohe-eurostyle-cosmopolitan-single-lever-bath-shower-mixer-33612002-spare-parts-[2]-122593-1-p.jpg
    grohe-eurostyle-cosmopolitan-single-lever-bath-shower-mixer-33612002-spare-parts-[2]-122593-1-p.jpg
    31.2 KB · Views: 30
Like this measurement bottom image. If that is the same you could have a thermostatic bath shower mixer or a tap that connects the same as yours.
Yes the measurements in that picture are correct. Do you have any suggestions on where to get the tap from? All my searches from suppliers have failed to provide dimensions on their taps. Ideally I would like to just replace the tap for a like for like but I can’t find one 🤦🏻
 
Yes the measurements in that picture are correct. Do you have any suggestions on where to get the tap from? All my searches from suppliers have failed to provide dimensions on their taps. Ideally I would like to just replace the tap for a like for like but I can’t find one 🤦🏻
Do you know where your bathroom came from? If you do you will be able to buy the same. Take a photo. You said you bought the cartridge for the tap. Did they know what the tap was? I will take a proper look when I get in.
 
Amazon normally have decent pictures of there sizes

Cheap and cheerful


Decent

 
As an Amazon Associate we earn from qualifying purchases.
Amazon normally have decent pictures of there sizes

Cheap and cheerful


Decent


I didn’t even think to look on amazon for a bath tap! Those dimensions seem to match up with mine, so guessing they should fit. I’ll give the cheap and cheerful one a go and easy enough to return if it doesn’t.
Thanks for all your help everyone 👍🏻
 
As an Amazon Associate we earn from qualifying purchases.

Similar plumbing topics

  • Question
Update: Perrin and Rowe have supplied a...
Replies
7
Views
537
  • Question
does a standard tap refurb kit fit? they come...
Replies
1
Views
383
  • Question
Hi, there is no grub screw. I have attached...
Replies
6
Views
418
  • Question
Just for future reference, a grub screw doing...
Replies
9
Views
825
  • Question
Thanks, I'll give it more welly!
Replies
2
Views
1K
Back
Top