Hose pipe size | Plumbing Jobs | The Job-board | Plumbers Forums
  • Welcome to PlumbersTalk.net

    Welcome to Plumbers' Talk | The new domain for UKPF / Plumbers Forums. Login with your existing details they should all work fine. Please checkout the PT Updates Forum

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

American Visitor?

Hey friend, we're detecting that you're an American visitor and want to thank you for coming to PlumbersTalk.net - Here is a link to the American Plumbing Forum. Though if you post in any other forum from your computer / phone it'll be marked with a little american flag so that other users can help from your neck of the woods. We hope this helps. And thanks once again.

Discuss Hose pipe size in the Plumbing Jobs | The Job-board area at Plumbers Forums

Status
Not open for further replies.
H

-=HaZ=-

Just wondered what size hose pipe would be best for using with a standard drain off, usually a couple of sizes in the shops, would 1/2 inch be the one???Thanks
 
Yes mate a lot of drain offs are tapered anyway.

I always use a jubilee clip as well, leaves you free to bimble off and do something else.

Also with the half inch you can link direct to lenghs of copper to syphon out cylinders and conect to other hoses to lengthen.
 
Last edited:
ive found the heavy duty yellow stuff to be the best it true half inch some of the cheap green stuff is a night mare to roll upand will not fit over tube without warming the end down side is you do have to use a jubilee clip on drain ofs
 
dont buy a cheap hose pipe, spend some good money and it will last you for years. i tend to buy 30-50m and break it down into 3-4 usable lengths, one very long for flats and a/c drain downs, a couple for downstairs rad runs and a short bit of a few meters to drain boiler and into a bucket.

i know it sounds alot but if you have enough to drain down/flush at 3 points at a time then you can save so much time.
 
Thanks for the answer and the extra advice, it has all gone in that brain of mine haha :)
 
If you're just draining it down for yourself, then ordinary garden hose will do (1/2"). If you're doing it often or in the trade, then get some better quality hose - not the thin stuff which kinks or splits after rolling it up a few times.
 
What I use is car radiator hose, I went to a hose specialist shop with a DOC gave it to them and they sorted the hose, not much bigger than a garden hose, cut to a length to suit me.

The advantage I found is that it doesn't go all floppy when filled with hot water, so works well on the customer who doesn't listen when you tell them not to put heating/hot water on the morning your turning up. It also coils up nicely and doesn't knot. Only a bit more expensive than ordinary garden hose.
 
Think I got my yellow hose at screwfix and it was about £11 for a large coil if I remember correctly!!
 
God, there really are threads for anything/everything.

Use a jubilee clip any old garden hose will drain a system.
 
bger 3 hoses and draining at same time, think of your profit margins!!!
 
God, there really are threads for anything/everything.

Use a jubilee clip any old garden hose will drain a system.

They won't actually. Some go rigid in the cold and kink. As mentioned above the Regin one is excellent (I have two) because it lays flat and doesn't kink. Makes the drain down a lot easier.
 
Status
Not open for further replies.

Similar plumbing topics

  • Question
Might be an air gap built in to the washing...
Replies
1
Views
224
  • Question
Take flow readings where ever you can. Just...
Replies
14
Views
943
  • Question
Morning gents and gals, I have a Milano Tower...
Replies
0
Views
759
Do what the rest of us do. Go to you’re local...
Replies
2
Views
717
  • Question
Yep metric and imperial versions most likely...
Replies
1
Views
227
Back
Top