Not another cheap tool alert.

[Whn1]

seriously it's not....
Whatd you guys think of this? Good idea? Useless gimmick?

Kamco Rad Hammer | System Cleansing & Accessories | Corgi Direct

 

[dancinplumba]

been out for ages, i just use my boots or a rubber mallet

 

[Destroyer2813]

Got mine free with my Magnacleanse, makes one hell of a racket when used in the drill and really vibrates the rads, on the plus side gets all the lost socks out from behind the rad quite easily

 

[Barry98]

How have you not been beheaded

 

[erpkid]

Strangely it does work and impresses /scares the heck out of the customers...............unless the rad brackets are a bit suspect as then it can cause them to fall off held on only by the pipes..........also it does rather bring out the dust from behind which rather takes the edge of the customer's original glee.

 

[Roger Welton]

Toolstation do a white rubber mallet, which is very good (non marking)

 

[REDSAW]

seriously it's not....
Whatd you guys think of this? Good idea? Useless gimmick?

Kamco Rad Hammer | System Cleansing & Accessories | Corgi Direct

awww!. not him again.lol

 

[TBServices]

Got the vibraclean. Does the job

 

[mcniven]

Haha class banter

"How have u not been beheaded"

 

[Roger Welton]

Any one tried one of these

MaxMag

 

[Mike Jackson]

Saw one in plumbs when the Fernox Rep was in. I tried to get him to give it me for free but he refused. He was raving about it and as there not a lot of money may be worth a blast as it's a lot quieter than the vibraclean etc. and not going to create any leaks like the vibraclean can.

 

[mjt]

Any one tried one of these

MaxMag

Like the look of this

 

[leaky]

got one given to me by a rep at phex manchester cos i bought a bit of gear and mithered the life outof him its dead good but you do need to rollit a fair bit to stir things up its a lot easier than hammers and stuff like that no noise no damage got to keep it away from wire wool or metal debri in the van cos it picks up these things and is murder to clean off

 

[AWheating]

i have the kamco rad hamma and its the nuts.

 

[suburbanplumber]

I have the Kamco
A: should be specified to wear hearing protection during use, [distant in 3, male monarch in 4] LOUD
B: a chap i often work with broke it by not tightening it up before using it
C: kamco will sell you a new nylon bit if/when you do break it
D: Will find socks, knock rads off walls and sometimes make holes in very rusty rads!

In short why would you have a powerflushing rig and not have one?
SP

 

[Roger Welton]

i have the kamco rad hamma and its the nuts.

I have also, It snapped the head from the shaft, phoned adey and they had a replacement to me the next day (lifetime warrenty)

 

[villa_tom]

seriously it's not....
Whatd you guys think of this? Good idea? Useless gimmick?

Kamco Rad Hammer | System Cleansing & Accessories | Corgi Direct

Are you on commission?

 

[Whn1]

Are you on commission?

[FONT=Tahoma, Calibri, Verdana, Geneva, sans-serif]I try to help my plumbing brothers out and look where is gets me.....[/FONT]

 

[dancinplumba]

Are you on commission?

stop it you !!

 

[dancinplumba]

I try to help my plumbing brothers out and look where is gets me.....

when ? ha ha ha

 

[villa_tom]

stop it you !!

Your flirting with me now....

 

[villa_tom]

I try to help my plumbing brothers out and look where is gets me.....

I know your only helping, but that sneaky 10% back hander makes it sweeter dont it......