Running a gas pipe HORIZONTALLY in a dot and dab wall | Gas Engineers Forum | Plumbers Forums

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Discuss Running a gas pipe HORIZONTALLY in a dot and dab wall in the Gas Engineers Forum area at Plumbers Forums

Status
Not open for further replies.

stratplus

Plumbers Arms member
Plumber
Gas Engineer
Messages
953
How many of you do this? New build included. Just going to have a look at 6891 to clarify my current opinion.
 
Yes behind the plasterboard but solid dabbed around a wrapped pipe.
 
Last edited:
most new builds have gas pipe wraped and fully enclosed in dab behind plaster board. som sites request steel ie on drops .
 
horizontally though? Seeing it quite a lot recently by 4 or 5 plumbers. Regs only give guidance on cavity.
 
BS 6891 (pipework) doesn't say that you can't run gas pipe horizontally but all pictured examples only show vertical pipework. I have just moved to a site where the whole gas carcass is ran horizontally around kitchen behind dry lining and they want me to do the same. I was always led to believe that pipework behind dry lined walls should be vertical only, wrapped and solid dabbed. Regs or standards don't seem to give me a reason to say I can't do it.
 
You can run gas pipe behind dot and dabbed plasterboard as long as the pipe is wrapped and fully encased with adhesive and takes the shortest possible route, but don't know if that applies to horizontal or vertical only
I'm sure someone will be along soon to quote the correct regs
 
I have only ever ran it vertically, chased in to blockwork, wrapped, plated and solid dabbed. I always found an alternative route to drop vertically to avoid horizontal runs.
 
Interesting one I've come across a lot of these recently too
 
Would you not have to vent the cavity so in the event of a gas escape there is a chance of it being detected?
 
That would've been my thinking IDChappy
 
My understanding is with say boxing, you have to allow high and low ventilation to allow for leaks non detectible by the standard tightness test duration.
 
Agreed Billy had this exact situation the other day where there was a very gradual leak which was virtually non detectable but could easily have collected in the cavity but for a fortuitously placed vent.
 
seen loads on site run horizontaly . I drop verticaly but not sure on the regs
 
yes you can run horizontally has to be wrapped and fully encased in adehsive so there is no cavity to fill up my problem with this is will the dry liner actually do what his told to and its unlikkley youll still be around when its done so how do you sign it of
 
Here it is, from the BS 6891:

8.9 Pipes in walls

8.9.1 Pipe runs
Installation pipe shall, where possible, be vertical and shall be placed in ducts with convenient access points or placed in pipe chases.
The installation pipe shall be secured and have as few joints as practicable.

COMMENTARY AND RECOMMENDATIONS ON 8.9.1
Typical methods of installing pipes in walls are shown in Figure 6.

8.9.2 Cavity walls
Installation pipes shall not be placed within the cavities of cavity walls. Every pipe passing through a cavity wall shall take the shortest practicable route and shall be sleeved (see 8.10).

8.9.3 Dry lined walls

Installation pipes installed behind dry lining shall be suitably encased by building material.

COMMENTARY AND RECOMMENDATIONS ON 8.9.3
For typical examples see Figure 6b) and Figure 6c).
 
The diagrams referred to in 6871 only show vertical pipe runs. No mention of horizontal.
Corgi book says horizontal pipe runs should be avoided.
 
"where possible". Site plumbers usually on price so "which is the quickest".
 
Status
Not open for further replies.

Similar plumbing topics

Make sure there is a means of isolating the...
Replies
2
Views
443
Lloyd999
L
Di do not know much about this heating stuff...
Replies
16
Views
2K
I took those photos! Looks like the only...
Replies
9
Views
2K
Experience tells me 10mm won't be enough but...
Replies
5
Views
846
Thanks all for your input, much appreciated...
Replies
7
Views
927
Back
Top