Sunday afternoon teaser | UK Plumbers Forums | Plumbers Forums

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Discuss Sunday afternoon teaser in the UK Plumbers Forums area at Plumbers Forums

king of pipes

Esteemed
Plumber
Gas Engineer
Subscribed
Messages
6,156
A little brain teaser for you chaps had a call yesterday my boilers not working ? see if you can spot what I found
 

Attachments

  • PXL_20210918_092441687.jpg
    PXL_20210918_092441687.jpg
    393.5 KB · Views: 74
  • PXL_20210918_092453334.jpg
    PXL_20210918_092453334.jpg
    284.3 KB · Views: 67
  • PXL_20210918_092432514.jpg
    PXL_20210918_092432514.jpg
    410.5 KB · Views: 68
Mouse powered boiler?

All the surface mount components look intact. Looks perhaps like one wire completely missing? as well as several damaged.

Interesting how repairable it might be considered to be, and who would want to attempt that. Need a quick way to tell if the circuit boards might be damaged before spending too long on it. I'm totally non qualified but I'd want to check the chassis earth all present and correct just as a first step. So interesting to me as a rank amateur (I wouldn't go near a boiler or gas) how much electrical training a gas engineer gets (and acquires).

Roy
 
A Proper boiler how often do you get to work on one of these and look at the ratio 😁
 

Attachments

  • Screenshot_20210919-162612.png
    Screenshot_20210919-162612.png
    1.4 MB · Views: 57
  • Screenshot_20210919-162558.png
    Screenshot_20210919-162558.png
    2.2 MB · Views: 54
  • Screenshot_20210919-162554.png
    Screenshot_20210919-162554.png
    1.6 MB · Views: 45
  • Screenshot_20210919-162547.png
    Screenshot_20210919-162547.png
    1.4 MB · Views: 36
  • Screenshot_20210919-162541.png
    Screenshot_20210919-162541.png
    2 MB · Views: 42
  • Screenshot_20210919-162535.png
    Screenshot_20210919-162535.png
    2.1 MB · Views: 38
  • Screenshot_20210919-162531.png
    Screenshot_20210919-162531.png
    2.3 MB · Views: 40
  • Screenshot_20210919-162522.png
    Screenshot_20210919-162522.png
    1.8 MB · Views: 35
  • Screenshot_20210919-162516.png
    Screenshot_20210919-162516.png
    1.7 MB · Views: 41
  • Screenshot_20210919-162511.png
    Screenshot_20210919-162511.png
    1.6 MB · Views: 47
Yes bud do it every year pictures are from a 2019 full strip down clean and service gets done like that every 3 years , and a interim clean and check in between , was booked to remove old shower doors and fit new ones there yesterday when I got the call "I've no hot water"a new PCB is on order and few wiring repairs and 🤞 hope she comes back to life 😉
 
Nice to see someone who can actually be bothered to treat an old boiler with some respect rather than just give it short shrift because it's old anyway.
 
Last edited:
0.0001 is the flue gas co/co2 ratio it tells us how well the boiler is burning, the lower the reading the better the combustion, less carbon monoxide is produced and put into the atmosphere 6ppm is very low for a old boiler and goes to show what can be achieved . Kop
 
Update fellas new PCB and set of electrodes and a bit of wiring replaced and she's back up and running new door and frame on order 😉👍. Kop
 

Attachments

  • PXL_20210922_083720930.jpg
    PXL_20210922_083720930.jpg
    278.6 KB · Views: 24
  • PXL_20210922_083644877.jpg
    PXL_20210922_083644877.jpg
    412.1 KB · Views: 32

Similar plumbing topics

  • Question
As an experiment could you go away for weekend...
Replies
13
Views
1K
  • Question
Yep metric and imperial versions most likely...
Replies
1
Views
982
  • Question
Is the plumbing copper or plastic? If the...
Replies
3
Views
868
    • Like
  • Question
Don’t believe what the package says only...
Replies
6
Views
792
  • Question
I second this. This is a mess and problem...
Replies
8
Views
1K
Back
Top