Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
Questions and plumbing advice in the UK Plumbers Forums - This is the UK Plumbers Forums. Plumbing threads related to UK rules and regulations. Advice for Plumbers in the United Kingdom. Keep Gas-related advice in the Gas Engineers Forum..
Normal Threads
My heating system makes a whistling noises immediately after being turned of or begins to cool...
Hi guys, I have a fault on a clients heating system whereby the heating will stay on regardless...
I have just installed a Thunderflush dual flush cistern outlet valve. The unit sits to high for...
Hi.. I would appreciate your advice.
I am not get any cold water on the bathroom. Just dribbles...
Hello,
I have UFH set up with a HIU in my flat.
My issue is that one zone (Bedroom 2) does not...
- shakeyjakey
- 9
- 2K
- Latest:
- shakeyjakey
Hi
I'd like to demolish this concrete and replace so as to move it 30cm to the left.
can I...
Hi, I have noticed recently that when the central heating, set at 60 on boiler, goes off the...
Contractor sub installed my new single kitchen sink and garbage disposal wrong. Sub had a "blank...
- Geolo85
- 2
- 927
- Latest:
- Down-the-drain-86
Hi all
Just had a new mains water pipe fitted and the hot water is very slow almost a trickle...
I have a waste pipe to install and it's giving this warning "Acetoxy sealants must not be used...
- Stratf01
- 6
- 1K
- Latest:
- Ben-gee
Hello.need a little help.
I have a water meter under kitchen sink next to stop tap and a water...
Having recently replaced my condensing gas boiler, i decided to upgrade two small double...
- jamesythe3rd
- 4
- 1K
- Latest:
- jamesythe3rd
When using solder ring fittings is it important to have one end of the pipe open to allow...
- Stratf01
- 5
- 947
- Latest:
- ShaunCorbs
Hi all. Due to current location of the existing stop tap, I was thinking about installing a...
- BananaBalaclava
- 6
- 1K
- Latest:
- BananaBalaclava
Hello everyone I am a female, level 3 student currently looking for an apprenticeship. I...
- Corrinabailey2764
- 0
- 774
- Latest:
- Corrinabailey2764
Have recently had unvented cylinder installed and when hot water is run it often makes a loud...
- Widdy123
- 1
- 1K
- Latest:
- oz-plumber
Just changed our cistern and found somone previously had used a random pipe for the flush pipe...
- Rachel101
- 9
- 1K
- Latest:
- oz-plumber
Hi all,
I can't locate the vent/drain valve on this manifold.
My manifold resembles the "UFH...
Hi guys. Do any of you knowledgable lot have any recommendations for hot water in a small cafe...
I am in the process of having an extension for approx 4m by 6 m including sky lantern
Whilst I...
Hi Guys,
I am looking to replace radiator as the old threaded valve is shot on this old...
I've spotted this rust patch on the outside of a cast iron radiator in the house.
There's no...
Hi, some advice would be great. I have an Instinct Eco-Mag fitted and it has started to leak...
Hi we have an Ariston new europrisma 10 UR 3KW heater and it has started to leak from a hole...
Got a porcelanosa shower mixer and i need to change the thermostatic valve. It shows that a...
- Hashtag246
- 1
- 768
- Latest:
- plumberservices
I have a water pipe (unpumped) from a stream in to my shed that houses a water tank. I require...
- GreenSelfBuilder
- 0
- 719
- Latest:
- GreenSelfBuilder
Issue with Samsung air to water heat pump
Over past 6 years we constantly get E911 faults, slow...
- johnfarrell8225
- 3
- 872
- Latest:
- ShaunCorbs
Hi all,
Sorry if it is a dumb question but ..
I just fitted a 1/2inch tap washer to my basin tap...
Hi,
I have a 40mm pushfit branch / boss that I want to convert to solvent weld.
I want to get...
- SWBR92
- 20
- 2K
- Latest:
- rpm
So these damn problematic vertical rads again.
I’ve had the Trv correctly fitted now but can’t...
- Moomoo
- 6
- 945
- Latest:
- Moomoo
New Threads
-
Determining the last radiator in the downstairs radiator runI am attempting to find out which one is the...
- Started by elmocambo
- Replies: 0
-
WAVIN (Hep20) UFH Actuator - is newer model compatible?Hi. Mil's UFH has Wavin 230V 2W actuators -...
- Started by DevsAd
- Replies: 0
-
New combi choice - manufacturer with the 'best' controls?Hi all. Asking for a friend who is getting a...
- Started by DevsAd
- Replies: 2
-
Are Pipe Heaters Safe?I have an ouside garden tap that freezes every...
- Started by Traveller 47
- Replies: 1
-
Choice of pipe for hot water secondary/recirculating systemWhat plastic based / barrier pipe can you use...
- Started by Failte
- Replies: 7
-
-
Vaillant echTEC Plus 838H over pressurisingHello. Not to long ago I took off a radiator...
- Started by lee2lee
- Replies: 0
-
-
Issue replacing 22mm pipe on central heatingHi all I was hoping to make good this corner...
- Started by kristeva
- Replies: 4
-
-
Inspection chamber leakWould someone be able to advise please. I’ve...- Started by BobThomas
- Replies: 8
-
Aliddin easyfit isolator, Anyone with a bad experience of these?Hi all, thinking of fitting the said isolator...
- Started by Barry
- Replies: 2
-
Ultra compact wall hung toilet frameI'm redoing our 4' x 4' downstairs loo. My...
- Started by UserError
- Replies: 1
-
-
So... Does anyone know what this is??As I said, any ideas what this is for? It was...
- Started by Jonnyfrance
- Replies: 5
-
Potterton Promax 15 HEBeen called out to an issue with a Potterton...
- Started by MethodPH
- Replies: 3
-
Best flush cones for low level cistern connections?Any recommendations other than the usual clear...
- Started by macka09
- Replies: 4
-
-
customer wants boiler in unheated storeroomunheated storeroom, with louvre doors open to...
- Started by Gasinspect
- Replies: 2
-
Seized Filling Loop TapHi, any ideas on how I can get this seized tap...
- Started by fadsarmy
- Replies: 1