Solvent weld gap filler? | Bathroom Advice | Plumbers Forums

  • Welcome to PlumbersTalk.net

    Welcome to Plumbers' Talk | The new domain for UKPF / Plumbers Forums. Login with your existing details they should all work fine. Please checkout the PT Updates Forum

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

American Visitor?

Hey friend, we're detecting that you're an American visitor and want to thank you for coming to PlumbersTalk.net - Here is a link to the American Plumbing Forum. Though if you post in any other forum from your computer / phone it'll be marked with a little american flag so that other users can help from your neck of the woods. We hope this helps. And thanks once again.

Solvent weld gap filler?

Post thread
Post reply

Discuss Solvent weld gap filler? in the Bathroom Advice area at Plumbers Forums

M

mutley racers

Esteemed
Plumber
Gas Engineer
Subscribed
Messages
5,168
Hi all. Has anyone used this stuff before when having a weep on a solvent joint? I got a joint on the soil pipe connecting to the underground drainage pipe which would be a nightmare to rip out?
 

Attachments

  • 16282717286763932961717142569981.jpg
    16282717286763932961717142569981.jpg
    521.3 KB · Views: 54
Sort by date Sort by votes
Can’t solvent underground it’s a different material
 
Upvote 0 Downvote
Not underground as that’s why they only sell it in push fit
 
Upvote 0 Downvote
Chip it off and use a pushfit coupling
 
Upvote 0 Downvote
mutley racers said:
I see floplast drainage pipe is made of UPVC which is what solvent weldis made of
Click to expand...
It will work as long as it’s pvc. The reason underground is push fit, is to allow the fitting to take up any ground movement, where a solvent weld would snap.

Rough up the pipe to remove the shine and use gap filler/thicker solvent, not the standard stuff, it’s too thin.
 
Upvote 0 Downvote
Timmy D said:
It will work as long as it’s pvc. The reason underground is push fit, is to allow the fitting to take up any ground movement, where a solvent weld would snap.

Rough up the pipe to remove the shine and use gap filler/thicker solvent, not the standard stuff, it’s too thin.
Click to expand...
The question is, would you use it on a pipe that is going to be boxed in and tiled? Would it be like using solvent weld and melt the pipe together or does it just set hard and seal the gap.
 
Upvote 0 Downvote
mutley racers said:
The question is, would you use it on a pipe that is going to be boxed in and tiled? Would it be like using solvent weld and melt the pipe together or does it just set hard and seal the gap.
Click to expand...
No I wouldn’t. Cut out and redo.

Get a pushfit coupling for the bottom, short piece of pipe, then a pushfit slip coupling for the top.
 
Upvote 0 Downvote
scott_d said:
I have only used it instead of solvent wend cement for loose fittings,
maybe a rubber glove and force it into the leaking area
Click to expand...
I am bemused why it is leaking. It felt like a good fit, I cleaned the pipe thoroughly and used pipe cleaner (usually just use emery) and there is a wee gap at the back. I tested it a few times and it was dry. Today it rained and I saw a damp patch behind it. Rain going down the vent. Bemused
 
Upvote 0 Downvote
mutley racers said:
I am bemused why it is leaking. It felt like a good fit, I cleaned the pipe thoroughly and used pipe cleaner (usually just use emery) and there is a wee gap at the back. I tested it a few times and it was dry. Today it rained and I saw a damp patch behind it. Rain going down the vent. Bemused
Click to expand...
If its just rainwater, can you cut off the fitting and fit this into the orange pipe?
1628280190985.png
 
Upvote 0 Downvote
Upvote 0 Downvote
mutley racers said:
It has a toilet and vent coming off of it. Would need to break out the concrete and cut the pipe further down and then use that fitting. Thanks for the suggestion though.
Click to expand...
Could you cut where the grey meets the orange, this would leave the glued part of grey fitting in place but not in the path of water, you wouldnt need to touch the concrete.
Then put that fitting inside and fit a slip socket a little higher?
 
Upvote 0 Downvote
scott_d said:
Could you cut where the grey meets the orange, this would leave the glued part of grey fitting in place but not in the path of water, you wouldnt need to touch the concrete.
Then put that fitting inside and fit a slip socket a little higher?
Click to expand...
Just had my 6 Yr old and 4yr old wake up at the same time and throwing up all over their beds. Been cleaning sick for last hour. Poor kids. All tucked back in bed and sleeping. Expecting a few more episodes thos evening.

Do you mean cut the pipe at the end of the grey socket just above the concrete in the picture?

This is my set up..
 

Attachments

  • 20210806_211927.jpg
    20210806_211927.jpg
    465.2 KB · Views: 37
Upvote 0 Downvote
WC1 said:
Have you looked at flexseal icon.

Flexseal ICON 4 Inch Internal Push Fit Drain Pipe Coupling | Drainage Superstore®

These innovative Flexseal ICON push-fit couplings are ideal for connecting pipes on the interior where external couplings might pose challenges. Manufacture...
www.drainagesuperstore.co.uk www.drainagesuperstore.co.uk
They are expensive but good and restrict much less than a transition type as above.
Click to expand...

Looks good. Although if I wanted to use this I would need to change the grey tee as the leak would still be in the pipe that is glued into grey socket. I was wondering, as I can reach my hand into the fitting, could I seal it that way with gap filler as surely there is a leak in there.

Talk about looking for an easy solution a
 
Upvote 0 Downvote
New posts

Similar plumbing topics

K
  • Question
Leaky elbow on bath drainage - I screwed up!!
Thanks I'll give that a go. I assume...
Replies
4
Views
676
kristeva
K
S
Advice on old Osma soil pipe boss
If the coupling fits, then no need for what I...
Replies
10
Views
1K
Timmy D
T
T
  • Question
How Robust is Solvent Weld Plastic Pipe
When it comes to solvent weld plastic pipes...
Replies
5
Views
558
pritchardsplumbing
P
C
  • Question
Fitting European shower trap to 40mm waste pipe
So have started fitting all the bits together...
Replies
15
Views
2K
Caveman
C
T
  • Question
Waste pipe -does this exist?
With patience, I’ve not come across a socket...
Replies
4
Views
882
Timmy D
T
Back
Top