What valve is the flow | UK Plumbers Forums | Plumbers Forums

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

What valve is the flow

Post thread
Post reply

Discuss What valve is the flow in the UK Plumbers Forums area at Plumbers Forums

D

dwalsh1

Messages
70
Hi all
I removed a radiator off the wall and forgot to note what valve was the flow as I'll be replacing with a new radiator with a trv. Without putting back and re connecting how can I tell what pipe is the flow and what pipe is the return because I assume the trv goes on the flow. Btw both plastic caps are missing off the valves. Cheers in advance.
 
Last edited:
Sort by date Sort by votes
In the absence of evidence to the contrary, your best guess is that flow is usually on the left. This is a rule of thumb, however, not a law of nature. Have a look at the other radiators in the dwelling, which side is the TRV usually on?
 
Upvote 0 Downvote
Link the pipes with a bit of tube and see which gets hot first
 
Upvote 0 Downvote
dwalsh1 said:
Oh right. They was attached to the radiator when I dumped it.
Click to expand...
These days trv valves can be fitted to either flow or return and work just fine. Just make sure that you read the information on the box. Seeing as you’ve dumped the rad valves with the radiator (ooopsie) make sure you get the trv and lock shield set. Some are sold trv only. Hope this helps.
 
Upvote 0 Downvote
dwalsh1 said:
I bought the above fittings like you mentioned and they don't fit the radiator valves. Surely you meant 3/4-15mm fittings?
Click to expand...

Did you remove the tail out of the rad as you’ve said you binned it you will need to buy more eg lockshield valve and a trv
 
Upvote 0 Downvote
dwalsh1 said:
So theoretically when I buy a new radiator and order the new TRVs I could use the tails temporary out of those am I right in saying
Click to expand...

Yes aslong as you get the same ones as your existing
 
Upvote 0 Downvote
Gasmk1 said:
Not if it’s one of mine I always fitted the air vent on the end that couldn’t be seen when entering the room for aesthetics
Click to expand...
I usually put the air vent where it is more likely to be accessible. Which usually means nearest the entrance. Now I wonder if I've been doing it wrong... but no doubt I'm not the only one so rules of thumb may not always work.
 
Upvote 0 Downvote
dwalsh1 said:
Also, washing machine hoses could be an option because they are the same thread as my existing valves. I'll buy a 2 metre hose and attach to both valves and see what gets hot first as they'll only be on for a few seconds.
Click to expand...
Hi mate, a mountain being made out of a molehill by a few here to be honest, get some bi directional valves and put them on, Danfoss ones are usually bi directional and it is far from the end of the world if they are the wrong way around, just out them on and if you get it the right way happy days.
 
Upvote 0 Downvote

Similar plumbing topics

Bottom
  • Question
Thermostatic Valve, fit to Flow or Return?
Recommend to fit on the flow pipe
Replies
2
Views
613
ShaunCorbs
ShaunCorbs
D
  • Question
Isolating valve
https://www.NoLinkingToThis/p/essentials-compressi...
Replies
2
Views
592
dwalsh1
D
M
  • Question
Pushfit fitting/pipe ok to rub against one another?
Thanks for the replies I decided to reroute...
Replies
3
Views
353
MiguelPlumbelo
M
S
  • Question
No heating flow. Pump and diverter working, what else could be wrong?
Problem found, it was a blockage... mostly in...
Replies
11
Views
1K
Stupot
S
Johnny1973
  • Question
Weird, nonsensical radiator problem. Out of ideas...
Will be a 15-60 then prob ups2 Green lights ?
Replies
8
Views
1K
ShaunCorbs
ShaunCorbs
Back
Top