Search results | Page 8

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Search results

  1. ShaunCorbs

    Would one radiator in this space be enough for 6.5 x 3.8m room?

    Roughly 2.5kw for a insulated cavity and one 1.4x1 m window So being a condensing boiler your looking for an output at cataloge around 4.8kw so your looking at two 1400x600k2 or two 1100 x 600 k3
  2. ShaunCorbs

    Is there any Gas safe engineer in Greater Manchester.

    Yes
  3. ShaunCorbs

    Dual fuel towel rail heating element

    No you can leave the central heating alone don’t have to touch it eg in summer when you want the electrical part to operate If you do run the central heating won’t harm it as there’s a thermostat on the electrical part so will just say it’s hot and turn off As for the buttons Top on and off...
  4. ShaunCorbs

    Is there any Gas safe engineer in Greater Manchester.

    Need to cold call people ask in merchants etc
  5. ShaunCorbs

    Long right angled screwdriver

    1/4 inch spanner and a 1/4 pozi bit ? Prob need to epoxy or weld it to the spanner so there’s no movement Or if you have room Milwaukee right angle attachment and a long 1/4 extension?
  6. ShaunCorbs

    Heating oil tank (plastic) has rusty coloured layer on bottom...

    It’s silt / sludge ideally need to run the oil low and clean the tank speak to your oil supply they might be able to do this for you
  7. ShaunCorbs

    UFH and zone valves help?

    Depends if they have programmable stats on the existing manifold / independent control on the new one etc
  8. ShaunCorbs

    trying to fix a Old very Large Tap in a Commercial Kitchen

    https://www.toolstation.com/flat-tap-washer/p25929
  9. ShaunCorbs

    Introduction quick hello from a diyer

    … hello and welcome…
  10. ShaunCorbs

    Domestic Gas in commercial properties

    Depends on the task but it’s the volume of gas in the pipework your working on As for how to work out the volume it’s the size of pipe find the volume 1m holds in your gas book then times by the amount of pipework in your section or divide by the volume this will give you a meters answer etc...
  11. IMG_8518.jpeg

    IMG_8518.jpeg

    • ShaunCorbs
    • Media item
    • Comments: 0
    • Category: Attachments from Threads
  12. ShaunCorbs

    Can anyone help an idiot diyer with a shower tray?

    Turn the waste fitting 45 so the angled adapter is straight at the back if that make sense
  13. ShaunCorbs

    Can anyone help an idiot diyer with a shower tray?

    you can but I would use the angled connector or a 45 degree bend see which one gets me closer and square to the wall wouldn’t use a flexi
  14. ShaunCorbs

    Can anyone help an idiot diyer with a shower tray?

    What’s the level say when it’s on the flats on the perimeter?
  15. ShaunCorbs

    Ideal evomax loses its settings if power turned off

    No there’s an on board battery
  16. ShaunCorbs

    DIY air conditioning system

    Can’t you get them to supply you the kit ? And you install it they vacuum and commission it ?
  17. ShaunCorbs

    Domestic gas appliance in commercial property

    It all depends on what your doing Servicing no providing it’s a stnd domestic flue and your not tt the whole line you can do a boiler tt If your replacing if there’s a local isolation valve and from that to the boiler is under the domestic regs eg 0.035m3 then your fine
  18. ShaunCorbs

    Honeywell 2 ports 22mm

    I’ve got 9 going spare does anyone need any not doing singles just bulk either 4s or 5s etc
  19. ShaunCorbs

    DIY shower with exposed pipework

    Can be done need to find on that either accepts 22mm chrome tube or you can use a male iron in the end
  20. ShaunCorbs

    G3 diy (Gods not available locally)

    https://electricaldealsdirect.co.uk/santon-aquarius-a103-10-litre-3-kw-vented-oversink-water-heater.html
Back
Top