fittings

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

Recent contents Top users
  1. C

    Tightening galvanised pipe and fittings

    I have a threaded galvanised tube between 2 T-pieces. I can’t screw the t-pieces onto the tube - they’re already sealed to the spur. So the only way I can screw the pipe between them is to screw it all the way into one side then screw it halfway into the other (by unscrewing from the first end)...
  2. L

    What manufacturer makes the best quality fittings for multilayer pipes?

    What manufacturer makes the best quality fittings for multilayer pipes?
  3. Ted808

    Where can I find compatible fittings?

    This a mix of material pipework and sizes. It's steel (what size?) and 35mm copper 28mm copper. I need to replace the leaky bit and tidy it up if I can. Where can I get the reducer from what I think is 2" steel to 28mm copper? Any pointers?
  4. G

    Help sourcing imperial fittings/adaptors

    I have a 27mm OD semi-flexible black pipe (PE?) feeding mains water to an annexe. I am struggling to source compression fittings to adapt this to metric pipe so that I can use standard modern components downstream. I belive the installation is about 50 years old. Is this what used to be 3/4"...
  5. T

    Corrosion on Pipe / Fittings

    Hi, I am probably being unduly paranoid here but I noticed under our kitchen sink that there is some corrosion evident on a small section of copper pipe between compression fittings on the hot water feed. There are take offs for an outside hot and cold tap together with isolation valves and...
  6. M

    Soil pipe/fittings 110mm sizes!

    It's not every day I deal with 110mm soil pipes, therefore I do not have a selection of different fittings at hand to try what combination fits my needs. I have therefore been trying to locate on- line the actual sizes eg length of push-fit tee, spread of branch, before I can purchase the best...
    • MalH
    • Thread
    • fittings soil soil pipe
    • Replies: 2
    • Forum: Boilers
  7. M

    Pipe fittings type for mixer tap

    Hello, I need some advise, will greatly appreciate if someone can help. My mixer tap is leaking from base want to renew it. However the tap cold/hot water feed is connected via connectors/fittings as shown in attached picture. Can anyone please advise how to disconnect tap from these fittings as...
  8. W

    What are these weird-a** pipes/fittings?

    Never seen them before. I just need to cap them off as they come out the wall... What would I need to do so (properly / safely)? Any idea why the fittings are all different colours too? Thanks
  9. W

    Is it ok to use male tapered fittings for female flexi ends?

    Or does the fact they are tapered mean the flexi might work it's way loose? e.g. https://www.NoLinkingToThis/p/flomasta-sfu-0269-brass-compression-adapting-male-elbow-15mm-x-1-2-/355kr
  10. S

    Faulty Hep2O fittings?

    Hi there, I am hoping someone can give me some advice. We have had two leaks at home in the last 2 weeks; luckily we were in for both events and managed to get the water turned off pretty quickly so it is not a massive catastrophe. Both times, a fitting popped off a pipe about 15 minutes after...
  11. P

    Soldering veiga fittings on gas

    Is there any clause that says I cant remove the rubber rind on a viega fitting and solder it on my domestic gas installation? Thanks
  12. O

    brass, stainless, or EP/plastic for Well service line fittings

    Where the black polyethelene service line enters this particular structure is by far the most freeze-prone area. The structure is an elevated "mini house" with an insulated, heat-taped plenum taking the poly from below frost line up into the space between floor joists. But, power outages...
  13. E

    Advice on shower tower fittings

    Hi, I have a shower tower fitted and my flexi pipes (500mm) are about 7cm short of where they need to be to fit onto the mixing valve in the back of the shower. I cannot move the shower up and the next longest flexi pipe I can find is 900mm, which is about 830mm longer than I need.. Would a 15mm...
  14. D

    Old pipe sizes and new fittings

    Hi, my wife decided she wanted new modern bathtaps instead of the old 'supertaps' we've had since we bought the place. So we bought the new taps and I tried fitting them yesterday but the new taps don't have the same fitting length as the old ones, this wasn't aproblem on the hot supply as...
  15. S

    How to remove these shower screw fittings from the pipes?

    I'm retiling my bathroom, and so everything in this photo minus the copper pipes must be removed. Anyone familiar with these screw fittings that go over the pipes? They have filed down areas to get an adjustable spanner in there to turn them, but when I grip the copper pipe and the screw...
  16. S

    Garden tap fittings query

    Hi - I'm a DIYer, successfully fitted an external garden tap, supply sourced from downstairs loo, standard 13 mil copper pipework, in-line cut-off. WEATHER PROBLEM - its worked fine for years EXCEPT twice now I've had split pipe due to freezing (at -8C ) despite foam protection. My thinking -...
  17. J

    MLCP Fittings dripping

    Has anybody had any experience of MLCP fittings leaking? I’ve used tweet top fittings on a few decent sized jobs and had zero issues, however I’ve just been to a job I’ve done and 3 fittings had a very small drip on them, crimp gun has been calibrated etc and pipework has been correctly...
  18. D

    Safety of shark bite type fittings in walls/ceilings

    I have had a copper pipe shark bite fitting fail dramatically resulting in lots of damage. This was in a ceiling application and done 11 years ago. Do I need to remove the 2 other fittings that presently look ok? For some reason I can not up load picture , but fitting separated about 1 inch with...
  19. M

    Shower head fittings for copper coonection

    I’m fitting an over head shower to an en-suite that I’m about to tile, I’m Struggling thinking about how to get the fittings flush to the tiles from the copper feed behind the boarding. Anyone any experience on the best way to sort this out? Cheers
  20. S

    Solder fittings advice pls

    When using solder ring fittings is it important to have one end of the pipe open to allow pressure and fumes to escape? I had a terrible job trying to solder a short section of pipe with an isolation valve closed on each end. It wasn't till I redid the work and opened one end that I could get...
Back
Top