install | Page 4

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

install

  1. D

    Can a new oil tank install be DIYed?

    Hi. Asking for a relative whose neighbour seemingly DIYed an oil tank replacement. She was aware of 'oil' smells at regular times in the weeks following this, although that has since died down. Is there a way of checking whether the installation was registered, a bit like boiler installs? Thanks.
  2. IanHoll

    Vertical Flue Install

    I've just had a Worcestershire Bosch installed by a gas engineer and heard him talking about having forgotten elbows, was it 90 elbows that he forgot and should have installed? The hole made in my ceiling is horrendous due to the 45 degree entry, but the plate he installed cover the mess. Can...
  3. B

    Shower bar mixer install?

    I’m installing a new shower bar mixer using a fixing kit which means I have to drill into the tile each side of the pipes to install the bracket. I do not want to hit a pipe, what’s the best way of doing it?
  4. N

    How to install hot and cold water to sink valve

    Hi folks, Newbie here. I'm having trouble connecting the washing machine hot and cold water valve to the below sink. As you can see in the picture, the valve is already connected to the sink above it. I would like to confirm whether I need to unbolt the below hex cap so that I can connect the...
  5. milleniumaire

    New kitchen tap install

    I need to replace an old leaking kitchen tap at a rental property and having fitted one of these before I've decided to go for the Cooke and Lewis mono mixer from Screwfix, which comes with 356mm flexible tales and a G 1/2" end: The tenant has sent me some photos of the existing tap and...
  6. V

    Cistern install

    Looking to rearrange the stud wall and the insulation in the wall in the picture below and install a cistern. Currently there's a plastic protective cover Infront of the insulation I was wondering if anyone had any tips on how deal with the cover and fix it up after I had done what I needed to...
  7. A

    Cooker install

    Hello, I've just bought an old mini Calor Gas cooker to fit in a shepherds hut. Can this cooker simply be hooked up to a propane bottle with an orange hose? Cheers
  8. M

    Flow rate new kitchen install.

    Hello again Guys I've just had a new kitchen install. The fitters tapped into the overhead 15mm hot and cold that feeds the Utility Room 3.0m further on. The hot flow rate in the Utility Room (Monobloc taps) is 9.5 litres/min. In the new kitchen monobloc the flow rate is 4.5 litres/min, less...
  9. L

    Shower Tray Install

    Hello...removed old shower tray and want to install a new shiny tray...see pictures How should I proceed ? Tray is ceramic about 50 kg Thanks in advance..
  10. D

    Looking for a Trustmark plumber for Rads/TRVs install Tamworth area.

    Afternoon all. Im looking to have a quote for supply and install of 9 radiators. Also, we would like to take advantage of the green deal offer as a secondary measure which includes supply and fit of TRVS. I wondered if it would be possible to incorporate a quote utilizing this scheme? Cheers Dave
  11. elvis80

    Shower pressure after UVC install

    Hi everyone - this is only my second thread on here, so I hope I'm observing all the rules...would appreciate your thoughts... We're in the middle of rebuilding a house and going from this system...: - 2 x bathrooms, relying on a gas combi and mains water pressure @ 6.5 barr, 1/2 inch main to...
  12. C

    Future ensuite - capped water / waste water install

    I am having a house built and I want to provide capped hot/cold water and waste water to a bedroom for a future ensuite. I don't want the builder to do the ensuite now because I am already over budget. They are saying they can't provide capped water and waste points to a non-wet area (i.e. a...
  13. E

    40kw Navien NCB Combi install with v.poor DHW? Is this adequate?

    Hi all, Just had a Navien NCB 40kw combi installed by an approved fitter. The DHW rates of the boiler seemed promising on paper - 16.4lpm at a 35 temp rise and 22.9lpm at a 25degree rise. More than adequate for what we need. The only issue now its installed is that I'm not getting any more than...
  14. shankly1985

    Dishwasher install question

    Hi all We looking at buying a dishwasher so I am checking to make sure we have all the correct inlets and outlets I believe we do but I would like confirmation please. This first image is below the sink. On the left is an empty drain connection I can use this for draining the dishwasher? On...
  15. avsmithy

    Water Softener Install - how long should this take?

    Apologies for the self interested thread, but I would very much appreciate the advice of you knowledgeable folks. I got a plumber in to install a water softener in my flat yesterday, I assumed it would be a 3 or 4 hour job, it ended up taking 12 and 1/2 hours. I do a lot of DIY, but don't know...
  16. M

    Install a tall 1800mm x 600mm rad in my bathroom fed from above.

    Hi everyone, apologies if this is a dumb question. I want to fit a tall rad in my bathroom which will be fed from above, but I would like to keep the pipework to a minimum. Is it necessary to run both pipes to the bottom of the rad, flow to the bottom and return to the top, or will it work with...
  17. B

    New boiler install - is this acceptable work?

    Hi I had a new boiler installed and wondered if you think this is acceptable workmanship. Looks like they started to drill a hole at the front and then had to move down. Thanks for your input.
  18. L

    Thermostatic Shower Install

    Hello... I have a Hudson Reed shower to install but don’t get this...see picture below.. The problem is once I do up the compression joints then the large O rings will not be flush against the wall...there is about two millimeters of distance between O ring on the large nuts and the wall..
  19. siricosm

    T50 on new install?

    I am about to replace my radiators (and piping) and doing the heat loss calculations. I am wondering if the T50 rating on radiators is still reasonable. Wouldn't T40 be more efficient with today's boilers, or would the difference be hardly noticeably? I guess T40 would also be at the upper...
  20. B

    Advice/confirmation for Nest install for Greenstar 30DCi classic boiler

    Hi all, I have read several posts and searched the internet and believe I have now got the correct procedure to install a Nest for my Greenstar 30DCi classic boiler with an Integral Diverter Value with a DT20 timer. If I could just get a second opinion, before I proceed it would be really...
Back
Top