mains | Page 4

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

mains

  1. B

    Where does my water come from if not mains?

    Hi everyone I was under the assumption that my flat was mains fed throughout but the water company said "We supply cold water to your cold kitchen tap". So my question is where does the water come from to supply water to the hot water taps in the bathroom and hot water tap in the kitchen? I...
  2. M

    Mains feed and vent pipe on vented system

    I have a boiler to swap on a vented system. The open vent was presently attached straight to the boiler. And the cold feed is tee'd in to the hot water return near the coil. When I install the new boiler (it's staying vented). Would I be best off changing the cold fill postion I will obviously...
  3. C

    Mains high pressure

    Has anyone come across extremely mains high pressure in a domestic property ?..? I used 2 gauges one at 6 bar and other at 10 bar both were off scale when static. I was shocked at the readings. Have since fitted PRV. Just seeing if people have experienced the same.
  4. B

    Does an unvented cylinder really have to be connected to the mains?

    This is my first post on the forum... but I've been around a while, lurking. Hello! I'm hoping someone can advise me with a question about unvented cylinders. I'm told they must be connected to the mains and can't be gravity fed, but I'm having trouble understanding why... if the pressure and...
  5. topalondon

    Leaking ball valve from outside mains

    I have a Plimex ball valve that is the inside stop tap for the mains supply that has recently started leaking. It’s only 2 years old (when property was renovated) and suspect it could be due to thermal cycling with the cold weather. Access is restricted as the pipe work was put behind a plywood...
  6. Scott_D

    Check valves on incoming mains supplys

    It’s been a long time since I did a wras course. Should you fit a check valve to a mains supply after the stop tap or is it a recommendation? Does this apply to new supply’s, alterations or all? I am quoting to replace this lot
  7. K

    Leaking mains stopcock

    The internal stopcock was closed for the first time in about a year as part of a bathroom installation. Now that it's open (I leave it a quarter turn from fully open) it has a slight leak, approx half an egg cup full in 24 hours. Should I get it replaced? Thanks in advance.
  8. D

    High pitched note from mains water pipes

    I have a flat in a 1920s UK block. The mains water feeds ~40 flats, of which I am one. There is no local boiler, though there is a communal one for the whole building. Recently, always at night, the mains water pipes have started to vibrate at a high frequency - emitting a "singing" note ...
  9. S

    Mains Pressure Tap above Consumer Units OK? UK Law *See Photo*

    I would like a professional plumber's advice on this attached image, which shows a mains pressure pipe with tap located above the consumer units. Is this ok for the legal requirements in the UK? Can someone let me know what the law is on this matter please? have a link? Thanks all.
  10. P

    Why is my mains water PRV not maintaining 3 bar?

    Hi all, I had a problem recently with the pressure to the house exceeding the 3 bar that the caleffi pressure regulator was set to. The gauge on it indicated that static pressure would sometimes increase to 6 bar; it's not just a gauging issue because the HW cylinder next to it starts leaking...
  11. DripsnDropsBognor

    Materials for back filling water mains trench?

    Hi Boys and Girls, I am splitting currently supply inside into 4 and upgrading old 1/2 galvanized supply from the street into building without breaking pavement into waterboard stopcock. I am using a moling company to bore pipe in through a trench I have dug out. I have agreed to make good hole...
  12. S

    change to 22mm pipe from mains?

    I live in a maisonette and there is a single pipe that comes in from the street for both flats. The pipe that enters the building is lead, probably 3/4, and is changed to 15mm copper pipe with an stopcock. This goes on for about 5-10m where it splits to both flats. Generally, water pressue is...
  13. D

    Old Welded Mains stopcock leaking

    Looking at the picture attached would you say that this old stop tap can be taken apart and the washer replaced rather than making the job more complicated than it need be. It looks like a really old type of stop tap situated under the kitchen sink flat to the wall with no space around it to...
  14. O

    Loss off water pressure after mains scale inhibitor fitted

    Hi all, i have fitted a 22mm scale inhibitor today( due to very hard water) and have lost pressure to all the cold taps in my property bar the outside tap and the washer valve feed . I have also lost around 4L a minute on the flow rate on all the affected taps . Property is a new build MDPE...
  15. T

    Baxi Burnall with back boiler connection to Unvented /Mains pressure water tank ??

    I have a Baxi Burnall open fire with wrap round back boiler connected via a Dunsley Baker Neutaliser to the vented hot water tank. I wish to update my older vented system to an unvented twin coil indirect water tank with two immersion slots. I want to use one immersion slot for my recently...
  16. S

    No pressure to mains water meter

    We’ve purchased a 1920’s bungalow that’s been unoccupied for a long time. I’m in the process of trying to sort the water supply at the moment. The water meter was submerged and when drained would quickly fill up again, we had south west water take a look, they said it was a leak on the service...
  17. J

    Why would cold mains feeding the boiler need an expansion vessel?

    British gas fixed a leak in the boiler and said the due to the recently installed water meter the fluxuation in pressure caused the leak. They advised to get a expansion vessel on the the cold mains entering the boiler. I read on here someone say that Worcester wouldn't warranty boilers being...
  18. Andrew Stride

    An old mains stopcock on an 30mm pipe needs replacing, please help.

    I need to replace the stopcock on an old mains water pipe. The house is about 60 years old, the pipes OD is 30mm, my local plum centre said they had no parts available to do this. The old stopcock is leaking and seized solid. Any advice about where I can get the parts to fix the problem would...
  19. R

    Wanted plumber to install new water mains

    I'm putting in a new rising main to my 1st floor flat. The pipe work is to run on the outside of the building in Insuduct. The water board will put in a new connection to the property boundary then a 750mm deep trench has to be dug to the Water Boards spec to the property (approx. 3m. long). I...
  20. deFoix

    Regular momentary dips in mains water pressure every 15sec

    Hi all, hoping for some help here. Over the last 2 months I've been experiencing dips in water pressure from my kitchen tap. The weird this is that these are momentary dips in pressure that occur every 15 seconds. It seems to happen in the mornings and evenings and is making my plastic pipes to...
Back
Top