Following completion of plumbing work today I would appreciate any advice on the following two issues :
Q1 I have had a 150litre horizontal indirect cylinder (Telford Brand) installed today on an unvented system. After the plumber left I saw the installation instructions which state –
“ The...
Hi all
I will soon be having a loft conversion, turning my small(ish) three bed one bath house into a four bedroom, two bathroom house. I am also doing a small extension and putting underfloor heating in that.
I am really confused about what I should be doing with my hot water / heating...
When you first open a tap pressure and flow rate is good, it then dies down like a combi would reducing from approx 20 l/min to about 10 l/m. Balanced cold doesn't have this issue, expansion vessel replaced due to being burst, couldn't clean filter in combination valve so temporary bypassed it...
Hi guys.
Just a quick question. I've been asked to fit a Worcester Greenstore unvented cylinder but I'm worried flow rate is insufficient. I measured the flow rate at 14 L/PM. It currently comes into the house in 20mm mdpe and goes straight to 15 mm after the stopcock to supply the house.
I...
Hi
Currently we've got a vented system in our 2 bed 1 bathroom 1st floor flat, which doesn't produce much flow for our mixer tap shower. I've decided to seek out getting a unvented direct cylinder fitted (electric only property). I've got three quotes and am in a quandary which one to go...
So I'm new to Internet forums and new to commissioning a new CH system... any help would be greatly appreciated, as I'm pretty confused by all the differing things I've read and been told regarding my current heating dilemma.
Background - I've just purchased a large 1900s 4 bed semi with 1...
Hello,
A couple of weeks ago I called out a plumber to change a thermostat since the bottom one (Economy 7) wasn't working. Unfortunately the change hasn't worked and since then (due to cost of calling in the plumber again to sort), I have been using the "Peak" switch for an hour a day to get...
HI Guys i had a unvented cylinder fitted onto my existing system boiler some years. The guy that fitted it didnt install an expansion vessel he just left the F+E tank in the loft. so we just have mains pressure hot water while the central heating is an open system. Anyway a month ago hot water...
evening folks, im putting an unvented in an old farmhouse in an upstairs room alcove area that will be eventually made into a cupboard.
being an old farmhouse, the floor is all over the place, I put a bit of fibreboard down and levelled it but the floor is out in a compound angle and is a real...
Watch out for this one, haven't resolved yet. Put in unvented cylinder for customer who wanted long 25 year guarantee. Cylinder installed as vented as they were willing to pay the extra. 2 years on cylinder develops a leak and customer told by manufactures there is no guarantee as cylinder is...
what exactly is done in an annual service for an invented cylinder? Other than checking no leaks, immersion elements are ok etc
I have my G3 ticket. But don't be fooled, they don't teach you much on the course!!!
Does anyone get involved in maintenance of UV cylinders?
Been sent this picture asking if I can have a look as it's leaking
Would you bother repairing a it looks to have multiple leaks and generally be in a bad state
Hello,
Having recently bought a new property which has an unvented hot water system installed, I'm just trying to understand what's normal and what's not so normal having had no experience of an unvented system in any of my previous properties.
My intrigue/concern really comes from when the...
Turned off mains, opened cold and hot side of kitchen tap, both stopped in about 30 seconds. Worked on toilet and changed some tap washers. Turned back on, all good pressure downstairs, hot and cold very poor upstairs.
Told her I'm not unvented so can't advise/deal with.
But did I do anything...
Guys looking for some advice
I have a property that we are working on we have the following
gnd flr
wc
kitchen with dishwasher and one basin
water softener
1st flr
ensuite
shower toilet and basin
ensuite 2
shower basin bath and toilet
2nd flr
shower
basin
toilet
washing machine
We have...
Hi all, I currently have a 15mm mains supply to a unvented cylinder in the loft as the pipe goes under a tiled floor en suite and it was not upgraded during the installation. I am now in a position to upgrade to 22mm but do I have to use a G3 qualified plumber for renewing the 15mm to 22mm...
Hello,
I have a Combi Boiler (Vaillant Ecotec Plus 428) and an Unvented Cylinder (Vaillant uniSTOR VIH GB 180s). Since yesterday we have no more hot water in the house, it comes out cold or luke warm. But the heating works fine.
When a hot water tap is fully opened, the boiler reads S.30 (no...
Hi Guys, just after some advice if someone could help.
I have a Aerocyl plus unvented cylinder in my house, Heat pump external (no gas)
I have a steady flow of cold water though the pressure relief tundish. Its constant as far as I can tell.
Going to call out a plumber tomorrow but in the...
about to hook up the flow and return to a santon cylinder that has been fitted for some time and using immersion only, the connections are not with the cylinder anymore, where can I get them?