Anyone knows a radiator wich has inlet and outlet roughly 40 mm from wall to radiator pipe centers(looking from side paralel to wall view).
I have ordered from mytub radiators, however got reply afer a day.
Order Notes:
------------------------ Steve 23.07.20 12:27 pm...
I am looking to steal a few inches from my bedroom, to slightly enlarge the en-suite and make the refurb job easier for a whole host of reasons. In undertaking this task i can go either with a 3” thick stud wall, or 4”.
I am thinking of fitting a recessed shower valve fixture and hence my...
Hi can anyone tell me how I can remove the pipe fitting from the connection. Is it the silver nut above the isolator valve I need to undo or the brass nut just above the pipe connection.
Thanks
Hello. I have a Nocode 510 wall mounted WC. Not sure of exact sub-brand. It's been working fine for 5 years but has recently developed a leak under the toilet. I've had a plumber over here twice 1) the first time to fix and replace the flush cone - which has led to a slightly bigger leak. 2) I...
Anyone had any experience with Cornish stone wall 470mm. I need to cut holes in it for a new kitchen waste and an extractor fan. Struggled just getting a 15mm pipe through as stone kept falling inside and blocking the hole. Any tips or advice would be greatly appreciated.
Hi All,
1st post on here and hoping someone can help out.
Im in the early stages of a garage conversion; I've temporarily hung the vertical radiator where its planned to go and my plumber has routed a couple of feed and return pipes in ceiling; i've attached a couple of photos showing the...
Hi all,
I'm a diy'er, and have previously tackled basis plumbing, fitting sinks, showers etcetra. I live in a two bedrooms bungalow. I have today moved a radiator from a side wall to under the window. This is to allow a bed to be placed on the side wall instead of under the window. All pipework...
I have a problem with 2 toilets fitted to a wall with the cisterns in the wall. I would like to replace them with standard toilets but the waste pipe seems too high (around 60mm above a standard toilet) and I don't have enough slope on the waste pipe to lower it. Are there any toilets out there...
we have mira excel bir shower and the shower head is not looking good all the chrome is coming of and we want to replace it. we canot get a replacement as they do not sell the logic bir head anymore it is only available with the full shower?
we had bought a difrent shower head but when fitting...
I have a Vitra reduced height 75/108cm frame to fit a Vitra wall hung WC to. I also have a 550 x 210mm cabinet to fit around it.
I have a few questions:-
1. To ensure the cabinet fits I have to fit the frame flush to the back wall and have had to remove the rear cross-member of the cabinet to...
If have the below shower/bath tap mixer to fit. The finish wall won't be tiles but plastic sheeting. That isn't too strong. So I want a way of fixing the shower to the wall before it's sheeted. Do I use the offset connectors supplied and a back plate elbow or buy shower mounting kit? It's on to...
Hi
Our plumber has just fitted a wall hung toilet frame. However he found that the frame to too tall and came above the window ledge. To make the frame fit, he has sawn off a horizontal bar at the top of the frame. The horizontal bar removed were where the brackets to fix the frame to the...
Am looking to fit a wall hung toilet in the next few weeks. I am completely confused by which frame to buy! Am I right to stick to something like grohe or gerberit...
Hi everyone, new to this forum and would greatly appreciate any advice.
We installed a walk in shower with a false wall to conceal the shower, toilet and wall hung sink pipes. There was a slow leak which led to a lot of mould growth. We opened the shower pockets and cleaned pretty much all the...
Hi - new to the forum, thanks in advance for any advice.
I have a Greenstar 30cdi boiler with currently a boiler mounted FW100 weather compensation controller. I would like to wall mount the FW100 to replace the old Honeywell T6360-1028 mechanical thermostat which is currently in the hallway...
The pan is screwed down using a Screwfix/Rawlplug fitting kit and I have sealed the pan to the wall tiles.
My question is: Do I need to also seal the pan to the floor tiles?
I think it looks neater without silicon to the floor tiles and it would create a sealed void should the cistern inlet...