Glad it’s not just me.
-
We recommend uHeat for Underfloor Heating Systems, and The Wetroom Store for all things bathrooms and wetrooms. They provide discounts for forum members.
Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
Anyone drive away from a job and then worry about if you’ve forgot to tighten any nuts
- Thread starter Dylandyl96
- Start date
Rob Foster
Esteemed
plenty of times ....worst one was 40 mile each way in darkest somerset, get back, hmm did I put the nipple back in the gas meter ? after drop test, return, ...hello mrs 'i left my wallet in the understairs cupboard ' it was ok
Rob Foster aka centralheatking
I think it's called 'plumbers paranoia'
That's a really good idea, my oh is particularly impressed and is going to trial that next week when locking up at customers (she does dog walking &sitting).
I'm really bad for worrying about this sort of thing, its bad enough with water, guessing its going to be even worse when I start working with gas! Still think its better to be overly paranoid than not enough.
Must admit I think any reasonable customer would really appreciate the honesty and the conscientiousness.
It’s not just me who has a photo album full of test points then🙂
From this post I have taken it’s a good idea to get into a routine on every job to check and test and forget it knowing you’ve done.
DGT plumbing
Gas Engineer
Yes, have that feeling most times about one thing or another, especially about did I turn the gas back on. Go through the sequence in your head and yes everything is always fine. It really screws things up when customers come and talk to you when your half way through doing something. Also left my mobile phone in an airing cupboard once after using the torch on it. Trouble was the number of the client was on it so couldn't phone them to ask them if it was there just had to go back to the property and see if my hunch was correct. Luckily they were still in so I was able to retrieve my phone after turning the van upside down looking for it.
dan_the_plumber
Gas Engineer
The trick is to link an action (eg, tightening a nut) to a memory.
It goes like this: ‘I know I’ve tightened this nut because at exactly the same time, I’ve looked at the clock and the time is exactly 11.22’
Or..,’I know I replaced that test point because right then the postman shoved a letter through the door and made me jump’
Honestly I’m the kind of guy that checks a door is locked 20 times, but using this method I’m almost always 100% sure every time.
For the few times now and then when you can’t quite remember if you did or didn’t, just go back! It doesn’t look unprofessional, if anything it makes you look more conscientious 🙂
It goes like this: ‘I know I’ve tightened this nut because at exactly the same time, I’ve looked at the clock and the time is exactly 11.22’
Or..,’I know I replaced that test point because right then the postman shoved a letter through the door and made me jump’
Honestly I’m the kind of guy that checks a door is locked 20 times, but using this method I’m almost always 100% sure every time.
For the few times now and then when you can’t quite remember if you did or didn’t, just go back! It doesn’t look unprofessional, if anything it makes you look more conscientious 🙂
Rob Foster
Esteemed
Yup, done that too, left mobile on a roof in Chepstow whilst shoving a liner down, went back , scaffold gone....its still there !
Meter test points always get tested with off once put back in. I stick to the routine so never worry. I do worry about flue gas caps tho but thankfully my analyser reminds me to put cap in when I turn it off.
Just a thought, but maybe flue test point caps should be spring loaded covers that just snap back closed when you pull the analyser probe out, so to be idiot proof. 🙂
bacon_sandwich
Gas Engineer
Yep, because i was that idiot. Found it on the following annual. It was the fresh air side, but nethertheless rather stupid of me. I too try and have a routine and never answer the phone during testing or any activity that has a sequence where i must leave it safe.
I normally leave tools and yes even testers onsite, not sure why, i guess its old age, they generally come back to me over time
I normally leave tools and yes even testers onsite, not sure why, i guess its old age, they generally come back to me over time
The first cylinder I did on my own as an apprentice, after doing my unvented course, late finish getting them up and running in one day, I literally didn't sleep that night. I even thought to myself "I don't know whether I can do this?" I phoned the customer first thing in the morning, sounding as confident as possible, "Just doing my routine thing and checking you have hot water this morning and everything is OK?"
"Lovely thanks, the shower is better than ever now, great job!" came the reply.
Phew!
Confidence builds, you stop worrying and then later down the line you get the "inevitable" leak and the confidence is destroyed for a while again.
Rob Foster
Esteemed
a water leak makes a worse mess than a gas leak ...sometimes.
Any decent tradesman or business man who never gets the 5 am's is either a liar or a conman . There will always be problems ...its how you deal with them that counts in my book Centralheatking
Last edited:
This is a very true.
Never doubt your own abilities.
I am the same but getting better now gsr for a year, but still over test and worry
So how do you connect to appliances as there’s compression fittings on them
We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.