Baxi Neta Tec - anyone fitted one yet?

[Heating-eng]

Fitting another tomorrow.

 

[Billy Bob Bob]

They seemed to have changed the blow off design on the netatecs already. It's now on the left.

wish they would put the pressure gauge on the front its stupid under the boiler same place as the old puma

 

[Heating-eng]

wish they would put the pressure gauge on the front its stupid under the boiler same place as the old puma

Yep I agree, does not look good. Also the front panel doesn't fit very well and could do with been better quality, really bad on duotec.

 

[Billy Bob Bob]

Yep I agree, does not look good. Also the front panel doesn't fit very well and could do with been better quality, really bad on duotec.

is there a big difference in price between the duotec2 and netatec on say a 28kw?

 

[Heating-eng]

is there a big difference in price between the duotec2 and netatec on say a 28kw?

Not sure, I fitted a 40 kw duotec the other day , it was about £900 I think.
The 24kw Neta is about £600 ish and the 28 is about £650 ish inc.
Not fitted any other duotecs.

 

[Billy Bob Bob]

about the same price wise as the mk1 duotec/heatmax

 

[Heating-eng]

Think it's the 5 year guarantee that is selling them at the moment, not sure what I will be fitting next year when that runs out.

 

[Billy Bob Bob]

yes probably as you know you only get 2 years with the mk1 and thats if your in the worx scheme,saying that i have loads of 6 year old platinum's with the 5 year warranty never seen heatteam then some the fan has died on swings and roundabouts i suppose

 

[Heating-eng]

I will see who offers a 5 year warranty and take it from there.
Got to say I do like the netatec though, small, cheap and built by baxi.

 

[Poxi]

cheap and built by baxi.

Ahhh those famous words LOL

 

[Barry98]

fitted another today , no problems so happy bunny

 

[Heating-eng]

Yes I fitted another today. Works great

 

[peter blanco]

out of fifthteeen fitted twelve have had various problems, inlet test point is really hard to get to, washers pack are slighty oversized so really difficult to fit when fitted to minium height to surface, gas valve problems diverter problems won't waste anymore time on them anymore!

 

[Heating-eng]

out of fifthteeen fitted twelve have had various problems, inlet test point is really hard to get to, washers pack are slighty oversized so really difficult to fit when fitted to minium height to surface, gas valve problems diverter problems won't waste anymore time on them anymore!

I read the instruction and follow what the rep told me, maybe I have been lucky but I think these are a really good boiler.
Think I am on about 10 now.
Please list all the faults you have had.
One thing for sure this is not just a plug in and play boiler.

 

[kevin h]

have fitted one and had problems with it,customer supplyed boiler because of 5 year waranty baxi wont honour that now because i didnt register with works first there was nothing supplyed with the boiler to tel me this . do me and the customer feel like weve had our pants pulled down =yes . these boilers and baxi support are crap,worster all the way for me.

 

[Heating-eng]

have fitted one and had problems with it,customer supplyed boiler because of 5 year waranty baxi wont honour that now because i didnt register with works first there was nothing supplyed with the boiler to tel me this . do me and the customer feel like weve had our pants pulled down =yes . these boilers and baxi support are crap,worster all the way for me.

What problem did you have.

 

[kevin h]

couldnt get it out of chimney sweep mode press the 2 buttons and display kept going back to 303 80, after spending about 50 mins on the phone to baxi and doing a re commition they said as it was working they would be round to look a week later, before week was up the customer had to phone them because heating hadnt come on they left him with no paperwork so dont know what was wrong.

 

[Heating-eng]

couldnt get it out of chimney sweep mode press the 2 buttons and display kept going back to 303 80, after spending about 50 mins on the phone to baxi and doing a re commition they said as it was working they would be round to look a week later, before week was up the customer had to phone them because heating hadnt come on they left him with no paperwork so dont know what was wrong.

In my opinion most of the problems are the engineers fault for not reading the instructions.
I always run the hot tap and have the case fully on before I fire it up for the first time.
At the moment I have had no real faults and have now fitted quite a few.
I would say there a great boiler for the money.
Baxi really need to change the set up of these boilers as most plumbers do not read or follow the instructions.
Not really baxi fault but they will get slagged off on forums.
I do agree there is some minor things that need to be changed.
The washers are to big.
The pressure gauge is hard to see.
The control panel is not of the best quality and doesn't close very well.

Now compair this boiler to any other in the same price range, the Neta Tec is by far the best. Ferroli or a baxi ? Lol

 

[luke2702]

Hi all, i am a commercial gas engineer and have just purchased one on the above boilers to be fitted in my home. Not sure if i am thinking i have done wrong...

Whats with the self commissioning?

I was talked into getting this by there rep in plumb in Manchester, got a 28kw, with flue kit and remote clock/stat for £680, so was pretty impressed. Boiler looks simple and easy to work on (he had a demo there), 5 year gaurantee, next day call-out etc..

Any one any info about commissioning side, as that seems to be were the problems stem from.

Thanks in advance....

 

[Heating-eng]

If you would like to ring me I can talk you though it. 01943876999
Tips.
Run hot tap all the time while setting up.
Make sure case is on do not start the boiler without case on.
Then just follow the instructions on the front.
I fitted a megaflow today and the set up is the same. Again I had no issues at all.
These boilers are very good. Most of the problems are installers not reading instructions or not following them.
Regards.

 

[Heating-eng]

Whats with the self commissioning?

Thanks in advance....

Clears all the air out of system before heat is added to protect boiler.

 

[luke2702]

Thanks for the reply mate.

When are you available to talk. As i am not fitting until Sunday. Just downloaded the installation instructions and doesnt seem to bad. Just doesnt mention about running hot type while it is going through sequence.

 

[Heating-eng]

Thanks for the reply mate.

When are you available to talk. As i am not fitting until Sunday. Just downloaded the installation instructions and doesnt seem to bad. Just doesnt mention about running hot type while it is going through sequence.

Ring me Sunday if you like. Really easy to fit. No it doesn't say about running hot tap but I was told too do it by the rep before I fitted any. I have now fitted about 10 or so now with no problems at all.

 

[Heating-eng]

Thanks for the reply mate.

When are you available to talk. As i am not fitting until Sunday. Just downloaded the installation instructions and doesnt seem to bad. Just doesnt mention about running hot type while it is going through sequence.

Very good boiler for the money.

 

[luke2702]

Cheers mate, expect my call at some point.....

Going from a Baxi bemuda 100 lol...

So just hope this is 100 x better....