K
Koogatubac
Lol all went inside the new baxi duo tec box btw the cylinder feed is a 30mm lead pipe with NO drain off
-
We recommend uHeat for Underfloor Heating Systems, and The Wetroom Store for all things bathrooms and wetrooms. They provide discounts for forum members.
Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
HALL of SHAME PHOTo`s
- Thread starter Barry98
- Start date
-
- Tags
- None
E
Ermintrude
No words required .
That's supposed to be a 75mm gravlon screed?
That's supposed to be a 75mm gravlon screed?
E
Ermintrude
Flexi-con patents pending I believe
E
Ermintrude
Vent / conny combo.
P
PlumbBobBob
obviously put the conny in before soldering
E
Ermintrude
I thought it was a making good effort after being sliced due to external 5m of flat 21.5 on its arse!
How did they glue everything on to the ceiling?
Bit awkward getting the vent key in that one
Bl**dy aussie plumbers....!
T
tamz
Self venting :wink:
Spending a penny
Found this under the floor of a house we were 1st fixing, this was a live, in-use gas pipe
This isn't a wind up, its genuine
It must have took longer to solder in position than it would have to go to the merchants (1/2 mile away) and get the right fittings
Just in case anyones short sighted, yes it is a one pence piece
Found this under the floor of a house we were 1st fixing, this was a live, in-use gas pipe
This isn't a wind up, its genuine
It must have took longer to solder in position than it would have to go to the merchants (1/2 mile away) and get the right fittings
Just in case anyones short sighted, yes it is a one pence piece
Attachments
T
TBServices
Me either lol
Open ended gas pipe? :grin: Nah, I'm not sure what the deal is either.
Also, dunno if you can really say this is worthy of the HoS but I haven't come across many bodge's lately:
Last edited:
No words required .
That's supposed to be a 75mm gravlon screed?
Last edited:
more concerned about how much that olive is on the pipe as it enters the elbow !!!
check the angle!
E
Ermintrude
From top down that's a 6*2 on its side to give sense if scale.
Next is the painted on gyvlon (Lafarge Tarmac screed) always called it gravlon after misquoted a drawing many moons ago. screed, next the clingfilm used instead of a membrane then the insulation then a 28mm gas pipe hacked off to allow shuttering !
Next is the painted on gyvlon (Lafarge Tarmac screed) always called it gravlon after misquoted a drawing many moons ago. screed, next the clingfilm used instead of a membrane then the insulation then a 28mm gas pipe hacked off to allow shuttering !
Last edited by a moderator:
So just a tad more than the 75mm depth you were expecting then ? still a good amount of thermal mass now!!
E
Ermintrude
Just worried that it's going to turn into crazy paving all because the builder is an idiot! Said he adjusted it all to suit Lafarge recommendations .... Strange only spoke to Lafarge two days before pour and the sub base , concrete DPC and jablite had been in for some week or two? Me thinks he is a gibbon who cannot measure or calculate such things as ; BOD (bottom of dig ) = FFL - (75 + 150+100+25+150) Gyvlon, jablite, conc, blinding sand , type 1
As for thermal mass it's similar to that of a paper bag and it's inertia could be likened to a carrier bag in a hurricane
Last edited by a moderator:
E
Ermintrude
Yep agree. Not like it's ever going to heat the 45m3 room with uninsulated flat roof and cold damp concrete floor.... Be wiser to have thermostat on the 25no g10 halogen down lighters !!
I
IDCHAPPY
K
Kyle87
As I was re-installing the bath the tenant said the basin water doesn't go down fast.....
I was like......."No s*** sherlock!!"
What you take the bath out for Kyle another smart person with taps at the back
We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.
