cistern | Page 4

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

cistern

  1. S

    Custom Flush Pipe High Level Cistern

    Hello, I’m trying to replace an antique high level cistern with a more modern ceramic one. The flush pipe is routed in a very specific way so the new one will probably need to be bespoke. Does anyone have any experience, or at least seen, bespoke flush pipes? I was hoping they could be made...
  2. A

    concealed cistern/pan compatibility

    I was wondering if anyone would know if this Tavistock wall hung pan would be compatible with this Geberit concealed cistern . I know they are from different manufacturers but I was hoping that the fixing and pipe centres would be standard. The fixing bolts appear to be right spacing. The waste...
  3. N

    Overfilling cistern - floating mechanism not halting inlet

    Hi everyone, First time poster, go easy on me! My toilet cistern seems to be overfilling. It's a narrow plastic cistern (not important I imagine) and thankfully the overflow pipe is doing its job. The floating mechanism is working in that it's moving up and down, though it has a lot of...
  4. I

    How to remove a glued cistern

    Morning everyone. We have a leak from one of cistern holding down bolts on our close coupled WC. This has occurred after a plumber replaced the flush valve yesterday. The problem is now that the plumber says he can't get the cistern off to replace the bolts because it is glued ( probably...
  5. Kerberos

    How high should a concealed cistern be?

    Hello, Getting some work done in my downstairs WC and my installer and given me a list of products to buy with some recommendations. We are replacing the exposed cistern toilet with a hidden one. It will be a back to wall, floor standing pan with a shelf above it to put stuff on. I've been...
  6. T

    Toilet issues, cistern not filling up

    Hi all, just a side note to start, I am not a plumber and have pretty much zero knowledge about plumbing. I have three toilets in my house, a downstairs one, big bathroom one and an en-suite one. There was a rattling noise coming from the downstairs toilet whenever the chain had been flushed...
  7. P

    Capping off and replacing an outlet for cold water cistern in loft

    Hi folks Following on from another thread I made recently, the plumber has agreed that the new cold feed he added to our loft cistern should have been lower than the existing feed to the cylinder for hot (he put them both roughly the same at 50mm) and he is proposing to put it right. In terms...
  8. A

    Cavity wall or ceiling cistern?

    I'm planning a wetroom in a very small space 1m x 2m (see attached). I want to maximise the space by having a cistern entirely in the stud wall including the waste . Two questions really 1. Is there a cavity wall cistern that fits completely inside a100mm cavity? 2. Is there such a thing as a...
  9. W

    Geberit slim cistern fill valve

    To get the latest geberit fill valve in to a slim cistern - disassemble and remove the part with "ears" that makes it too fat for the cistern width - then reassemble. Use the clip from the old fill valve to reattach.
  10. mudson

    Finding a new cistern to fit my close coupled toilet

    Hi - I have an old (maybe 45 year old) Twyfords Close Coupled toilet. The cistern has cracked, and I'd like to replace just the cistern. I'm struggling to find anything described as a close coupled cistern which doesn't have the bolt holes. I was hoping to find one with no bolt holes and just...
  11. A

    My Saneux FL2026 (concealed cistern) push buttons not working

    We have model number FL2026 concealed cistern - picture attached. The system is not working when pushing via the buttons on the plate. It used to work when we push directly after removing the plate. Even this has become hit and miss now - specially with the yellow button. The pins (used to...
  12. P

    Geberit concealed cistern Leaking into Wall…

    Hi all, I was just posting on here to see if anyone has had anything similar or can point me in right direction… I have a Geberit concealed tank within the wall so a floating toilet and over recent weeks have found that the brick work just outside of the toilet area (downstairs toilet) has...
  13. C

    2.7" cistern flush

    We are trying to replace the push button flush on our toilet. We've got a replacement flush, that includes seals for 1.5" and 2" cisterns, however the diameter of the hole at the bottom of our cistern is bigger, about 2.65cm/2.7". We've attempted to use the 2"seal,with the old doughnut seal...
  14. P

    Roca Duo in wall cistern how to remove plate?

    Hi Guys (and Gals).... Just moved into a new house, all fine, except today the main bathroom cistern started overflowing (into the pan). I think its a Roca Duo, with the L1 plate (from the Roca website). I've watched a couple of youtube vids on how to check these etc, but I've failed at the...
  15. N

    Cistern push button size question

    Recently replaced an enclosed cistern with one of the exact same size but the new push flush button (pneumatic) is far larger than the old one (cable-operated). We would prefer to keep the smaller button but have been told that the large button will be needed to effectively operate the cistern...
  16. T

    Slow filling cistern, lot of air

    The cistern has been filling fine for nearly a year, then in the last week or so it has been taking ages to full. Taking thr cover off the symphonic release is working and sealing fine upon completion. The float on the fill is working, but when it's filling their is a trickle and a fine spray...
  17. M

    Where Can I source a Duravit Cistern spare

    My cistern is in a perpetual over flow state due to the cut off valve not working. I think I have narrowed it down to the cut off arm (see photo) but where can I source a replacement?
  18. W

    Cistern i.d please ?

    As pictured. It's the one with the sort of claw at the end of the cable. Can't remember which one it is. Thanks
  19. P

    installing a new cistern

    hi all, i couldnt find exactly my issue, as i dont know what this design called. im fitting a new flushing and filling mechanism. the filler element is the problem, as the pipe that connects to the cistern tap (the quick shut off one) is flattened?! so its a half the thread, and the sides of...
  20. O

    Multikwik Multiflush Cistern Overfilling

    My regular plumber wasn't available so thought I'd have a go. Long story short, flush button broken and couldn't get a compatible replacement. So I bought a Multikwik Multiflush. To my surprise, I successfully installed it but when I flush, the cistern continues to fill. Apparently, the...
Back
Top