fittings | Page 8

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

  1. Z

    Rinnai Infinity 16i gas water heater - no boiler fittings

    Hi, just purchased a Rinnai Infinity 16i gas water heater from Mr. Central Heating. Boiler and flue arrived but fittings are missing. Its got 3 x 1/2 BSP brass male connectors coming out of boiler. What's needed and where do I get it from? Gas installer advised that these should have come with...
  2. S

    Yorkshire fittings help

    I decided to try Yorkshire fittings on the new kitchen build. Normally with me being a novice I used compression fittings in the past. So with the Yorkshire fittings I watch how its done on You tube. Easy I thought, how hard can it be???? So I bought all the gear and stated to follow the you...
  3. E

    Pipe coupler issue - connecting two male fittings

    Hi there I'm trying to connect two male 15mm x 3/4 inch pipe connectors together. Can anyone advise the adapter I need and where to buy it from? The problem is shown below. Note: This issue occurred because I am trying to tee off from the kitchen cold water pipe to supply an outside tap...
  4. bright spark

    Making compression fittings in tight spots

    Does any1 have any neat tricks for working on compression fittings in tight areas. Does any1 use any ratchet spanners etc or just take lumps outa your fingers. i know push on fittings are a god send but can't b used on gas. thanks
  5. N

    HPB15 fittings

    Hi, Got two pipes, 1 hot & 1 cold feed that I need to permanently stop off. The pipework is grey plastic & the fittings say HPB15 on them. Has this been superseded by HEP 20 ? If that's the case can I simply use the HEP 20 blanks? Thanks
  6. R

    Plastic tee fittings near boiler

    Hi, i'm installing a bathroom and need to install tee fittings into existing hot/colds. The best place to do this is near the boiler, however someone told me you cant use plastic pipe/fittings within a certain distance of the boiler. The best place for the tee would be about 2 feet away from the...
  7. D

    Replacement Three Way Valve - Including Pipe Fittings

    Hello folks. I need a replacement 3 port valve for my central heating system. The current unit I have is a Siemans / Landis & Staefa RHM mid port 3 way valve. This one: heatingsparescentre.co.uk/siemens-c25/motorised-valves-actuators-c3028/siemens-rmh-2-3-port-spring-return-actuator-p22514 I...
  8. M

    What size pipe insulations fits over 42mm compression fittings?

    Hi, All in the title really, What size pipe insulations fits over 42mm compression fittings? I don't have one at hand but need to place an order for some pipe insulation. Im thinking 54mm but not sure. Cheers!
  9. E

    push fit fittings on unvented cylinder

    looked at an install today and the pressurised cylinder cupboard ws completed in push fit. The tundish hadnt been conected yet but wht are peoples views on it. i personally only use copper but am told plastic is ok. Eddie
  10. M

    Polyplumb fittings

    I have a grey polyplumb elbow that I need to remove one of the pipes from to replace it with a longer length. I assume ideally I would use one of the component kits on the new piece of pipe, however, I have a new unused straight coupler and I wonder if it is acceptable to take the end of one...
  11. J

    15mm glued Plastic pipe & fittings

    Hi Guys Hoping someone can help. Came across a house in Devon completely plumbed with glued 15mm PVC type hard plastic pipe. (The lady wanted a basin replacing) The tap connectors were brass/copper imbedded in a plastic pipe connector, the pipe and fittings are white, with '15mm made in uk'...
  12. I

    Installing plumbing fittings so they are removable on unmovable copper pipe

    Is it possible to install compression valves onto existing non-pullable copper pipe WHILE designing-in a means of being able to replace the whole valves should they fail? Hello, I have existing 22mm copper pipe that needs a small section cutout to install a compression isolation valve...
  13. Chalked

    Plumb Center copper fittings

    Who makes thier end feed range? They are reasonably priced, but one end will be tight and needs thing on and the other side is slack! im going back to yorkshire endex. Rant over :censored:
  14. S

    Some sort of mould on compression fittings

    Anyone came across this before on brass fittings stored in shed. Any suggestions on how to remove it. Tried wire wool, cleaned in hot soapy water and left to soak in boiling water. Anyone know of a chemical that could remove it?
  15. J

    Press Fit Fittings for Copper and Plastic

    Hi I just purchased a Milwaukee M12HPT Hydraulic Press Tool and was looking for some opinions before buying jaws for it - been struggling to find a huge amount of information on the internet! I really don't want to buy multiple sets of jaws, would prefer to stick to one profile, but there...
  16. T

    Compression fittings to Cylinder

    For one reason or another, I seem to have had some pretty poor quality compression fittings of late and had to rely on boss white to seal. Not sure if its poor olives (brass v copper). Anyway, I'm about to replace my indirect cylinder and while cold feed, and coil feed and return will require...
  17. J

    Waste pipe fittings

    I am replacing the soil pipe and external bathroom waste pipework, but cannot find any fittings on connecting the "white plastic" pipes that come from the bathroom suite to the "black plastic" external fittings that match the black soil pipe. As you will have guessed I'm very much an amateur...
  18. Chalked

    Uponor mclp fittings

    I have around 100 mclp crimp fittings in 16mm, 20 & 25mm. Tees elbows and sockets. Reason for sale is, main builder where I have to use plastic pipe, likes Uponor Q&E so I haven't used any for a year. if anyone uses mclp crimp fittings post on this thread. If any interest, I will take some pics.
  19. A

    Old wavin fittings

    Hi there does anybody have any Wavin Osma Amazon ... I need a 7T.754? Help
  20. G

    Black 40mm compression waste fittings

    Why is it impossible to get hold of these or am I not looking hard enough?
Back
Top