fittings | Page 6

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

  1. A

    Why different forces are needed for 110 mm soil pipe fittings?

    Do you know why some 110 mm soil pipe fittings are easy to push into the soil pipe, whilst other fittings are much, much harder to get in, given that they all need to do the same job of making a gas tight and water tight seal? Recently I found that I could easily push into the soil pipe the end...
  2. R

    Victorian Brass Pipe Compression Fittings

    Hello all, I am hoping to get some advice on a small project I am working on at the moment. I have a lovely old victorian towel rail which I am trying to modify to make it smaller. Its just too big for out house. It is made of Brass pipe and fittings, 1 1/2" . The Brass pipe has a flange end...
  3. M

    What best to replace this collection of fittings?

    Help! I have uploaded a photo of fittings that have been weeping, for a long time, beneath a sink in my daughters (recently moved in) house. The hot water had to be turned off because of big leak under floor. The pic shows tails from the mixer tap, beneath which is a stop valve, with no...
  4. J

    Compression fittings. How tight?

    Hi all I have just finished the last thing in our ensuite. The thing I was most worried about actually. I had to re-install the shower valve onto my new pipework. Anyway, after installation I had a few little drops of water from one of the compression nuts. I nipped up the nut a little more and...
  5. Bogart

    End feed fittings being awkward.

    Am sure is not me as I have done end feed fittings before with no problem. What I am experiencing is that after cleaning up the fitting and the pipe they slip into each other fine but after I apply flux they do not. If I try to turn the fitting on the pipe a lot of the time it is very hard...
  6. D

    XPress fittings, pros and cons. Opinions please.

    Hi, looking at getting into press fit fittings as I like the speed that they can be installed on copper, and without a flame, or a big ugly plastic or compression fitting. They look great and earth continuity is maintained and are tamper proof on copper. The fittings are also inexpensive. Apart...
  7. S

    Plumbing fittings prices

    Hi I would like to start selling plumbing articles but I do not know exactly the prices in England. Is anyone this forum can tell me these wholesale prices are attractive on this market? Brass nipple 1/2' – 0,41£ 1'- 1,45£ MDPE coupler 32-2,15£ Thank you for your help
  8. S

    Push Fit Fittings and rotating

    How far can push fit fittings be rotated after being joined, i need to wallpaper behind a radiator that I don’t want too remove. I have a pic just know were too host it. 45/90 degrees possible ? FOUND AWAY TOO ADD THE PIC IMG_0316.JPG Thanks in advance Steve
  9. N

    Cast iron radiator fittings

    Hi all I am converting a 1910 community hall. It has 3 original cast iron radiators which are in good order but were installed via big steel pipe. The radiator fittings (connectors) are a big problem. At one end I have a steel pipe coming out with a 14tpi three quarter BSP tapered thread, that's...
  10. D

    Need to find out how I can remove soft-close top fix toilet fittings?

    I have the job of trying to remove the fittings for an existing soft-close, top-fix, toilet seat. The problem is that I cannot get the 2 existing bungs and one stubborn machine screw out of the holes in the porcelain. The screw just goes round and round in the hole - it won't unscrew out and it...
  11. R

    Are any fittings allowed on mains in before the stopcock?

    My stopcock is in a difficult to access location behind kickboards, can I put a coupling on the mdpe pipe coming up and into the house and move the stopcock up into the cupboard under the sink? Just wondering if any fittings are even allowed between the mains shutoff in the street and the...
  12. J

    320+ x Geberit Mapress Plumbers Fittings Stainless Steel 316 & Copper Job Lot

    ALL FOR SALE 33 x 1.4401/316 - ø28/ø15 10 x 1.4401/316 - ø22/ø15 19 x t connet ø15/ø15/ø15 26 x 90 degree ø15 17 x ø15/R 0.5" 02 x ø15 45 degree 06 x ø15/Rp.5" 11 x ø22/ø15/ø22 06 x 22/22/22 02 x 22/22/Rp.5 09 x 22mm chrome elbow 09 x 22mm chrome straight 05 x 15mm chrome elbow 03 x ø22/R.5"...
  13. P

    Plumbing fittings for sale in Macclesfield

    Hi everyone, I haven't been on the forum for a long time as I have retired from plumbing. On clearing out my garage I have found a roll of 10mm copper, numerous copper fittings, stop taps , gate valves , speedfit pipe with fittins and inserts, a couple of TRV's some waste pipe fittings etc. I...
  14. gmartine

    Storage for fittings?

    Thought it was good value (its huge), catches probably wont last too long. Powerfix Profi XXL Organiser Box - at Lidl UK
  15. M

    Half inch or 15mm pipe fittings question

    Hi folks Need some help ASAP please. I cannot fully turn of the mains inside my property due to very old stopcock under kitchen sink. Property has two stop cocks internally (house is 1930's build) with the first being made of lead on one side of stop valve and copper coming out of the other...
  16. W

    Can you anyone tell me what fittings these are?

    1.5" solvent weld plastic comes through wall from kitchen sink and down into this. Needs repiping due to bad joint. Would ideally like to pipe down as low as I can go without disturbing the bits actually in the floor but don't recognise the fittings below the coupler. Couldn't even feel...
  17. R

    HBP Fittings - demountable?

    I'm pretty sure I know the answer but these are not demountable are they? It think it's going to be a drain down and fit compression. She's left it that long it's wrecked the floor under the lino.
  18. R

    38mm antislip ring pvc compression fittings

    I am replacing the seals on washers on my sink waste trap. Can the 38mm anti slip ring/washer be bought alone as there is nothing wrong with the actual fittings. I can find the rubber seals and I can see 38mm trap washers at Toolstation. Are these right or can red/blue ones be bought? And why...
  19. J

    Help with non existent pipe fittings!!

    First of all I know nothing about plumbing I apologise for any errors. This is for connecting mains water to a caravan. I need to link a black 28mm (pvc?) mains water pipe that cannot be pulled up or replaced into a 25mm mdpe pipe. The 25mm connects to 15mm in the caravan, so the 25mm could...
  20. C

    How to join threaded brass fittings

    Hi. I'm fitting a new shower valve (Grohe Rapido T universal) it has 1/2" inlet and outlet ports to connect to so have got some 15mm x 1/2" male unions (I think that's the correct term) both straight and elbows. I've tried to find out how to fit the brass fittings and there's lots of...
Back
Top