fittings | Page 5

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

Recent contents Top users
  1. J

    philmac fittings blowing off.

    hi folks, I have a problem with a fairly new housing project. I have philmac pipe 25mm connected below sinks onto a philmac union and they keep blowing off, I have had scottish water to the properties who have tested the pressure which is sitting at 5 bar, pipework does not have any clips below...
  2. T

    Identification of toilet cistern fittings

    Hi P{lease can anyone identify which manufacturer and model is shown in the photos. The flushing valve is leaking water into the bowl and suggestions for replacement will also be helpful Thanks
    • Teka
    • Thread
    • cistern fittings toilet
    • Replies: 1
    • Forum: Boilers
  3. Plumbase Spares

    How Bristan EasyFit taps simplify kitchen fittings!

    Homeowners always keep up with the latest trends in kitchen refurbishments and ways to cut down costs. So, plumbers and installers need to ensure they can offer their customers competitive quotes, whilst maintaining margins by cutting down installation times. On average, replacing a kitchen...
  4. B

    damaged tile on shower fittings

    Hi all. Any idea on the best way to repair this quite visible chip around the shower tap fitting? Is it a matter of trying replacing it? what is the best way to solve the issue avoiding damage to the other tiles and to the shower screen (frameless one with hinges attached to the adjacent tiles)...
  5. D

    Old Hep fittings?

    Hi, Thanks in advance for any advice! I'm helping a friend with his water pipes, and I'm wondering about the grey fitting in the picture. We just bought some HepKeys which successfully dismounted the white fittings, and I'm wondering if the keys would also dismount the grey fitting, as I'm...
  6. M

    MLCP Pipe & fittings - press fit

    Hi After a recent job needing some parts I’m thinking of using this stuff on a job that’s a I start soon. I’ve a quick look online though and not that many places seem to sell much of it. For those who use it already, what manufacturer do you use and where do you buy it from? Cheers Martin
  7. Plumbase Spares

    Exclusive Endfeed Fittings offer - 24 HOURS ONLY

    Consisting of quality Endfeed fittings, that are WRAS approved and manufactured to EN1254-1, this pack provides all the fittings you need for standard water and gas application in an easy to handle and store bucket. CLICK HERE
  8. L

    MDPE pipe and fittings, are all equal? What durable brands to buy?

    Dear All, Whenever possible I aim to buy the correct quality product the first time round. Plumbing labour and water damage is expensive, thus, very happy to pay quite a bit more for materials provided it is needed to ensure a lasting product over time. Your advice will be much appreciated...
  9. D

    New Polymax fittings from Polypipe

    Has anyone used the new Polymax fittings from Polypipe? I've just ordered their free sample pack to try them out. From photos, they look almost identical to Hep20.
  10. E

    Least Bulky Plastic Fittings

    Hello, I want to extend a radiator using either PEX or HEP20 pipe, which type of pipe has the least bulky fittings as I need to fit under floorboards.
  11. gingalig

    Press fittings gas mechanical or not

    Hi I spoke to gas safe today as wanted clarification that it was or was not considered a mechanical fitting using press fittings on gas pipework, the response was that it was to new to call and i would need to speak to the manufacturere, long story short and a lot of call waitiing and i didnt...
  12. H

    Mixing metals on compression fittings

    Annoyingly I have used a copper nut on a steel isolation valve and the corresponding steel nut on a compression copper fitting (15mm). Should I dismantle and redo? I will have to buy a length of plastic pipe and new olives as well as drain system. Or will it be OK?
  13. M

    Identify Fittings on HW Tank

    Evening All Can anyone advise me what these fittings are? Hot water cylinder, 22 mm pipe, is this a male or female fitting as I'm looking to fit a Warwick flange or similar for a shower pump. Many Thanks
  14. K

    Shower digital mixer valve compatibility with regular fittings

    Apologies if this should not be posted here (I have posted to the electricians forum, however just realised the plumbers forum seems to have many more posts covering this mixer unit) I have a pretty basic question on suitability of a shower digital mixer valve. Checked with the the manufacturer...
  15. D

    kitchen sink fittings

    I've just moved into my first property and I'm clueless when it comes to plumbing, I'm tight on cash right now so I'm looking for some advice please. I'm looking for general advice on what I will possibly need to connect a trap to my sink. I have no idea what the white modified connection is...
  16. B

    Fittings to branch into cast soil pipe?

    I would like to add another WC about 2m to the right of existing WC. The existing soil pipe has only one WC (coming out the wall straight into the soil pipe) and is a straight vertical cast iron 4 inch pipe with a vent at the roof. My plan is to go out the wall with the new WC and then go down...
  17. J

    Looking for some advice on new toilet fittings

    Hi all, Got a tiler coming around to tile to toilet and thought i might aswell replace the old toilet. Problem i can see is if i order a new toilet there is gonna be a big chance that the water feed pipe going to the old cistern will not line up with the new cistern. I was thinking if i cut...
  18. D

    Fittings needed for freestanding taps

    Bought this discontinued bath and freestanding bath taps from Wickes. The taps were quite discounted mainly due to the fittings that couples the unit to the hot/cold water pipes have been misplaced. So I'm trying to find/buy the correct fittings so I can connect this to the hot/cold water...
  19. A

    Is white PTFE tape allowed on gas fittings these days?

    Ex gas fitter here. I haven't worked on gas for at least a decade so I'm not up to speed on any changes there may have been since I last worked in the industry. However, I have recently gone to a family members house who has had a new kitchen fitted. I couldn't help but notice that the gas...
  20. J

    Help to identify fittings & pipe please

    Hi all, Went to survey a job yesterday and need some help to identify fittings & pipe please - see pic. Many thanks in advance. Cheers Jim
Back
Top