Hello,
Been out to one of my ladies and she has filled her CH system with a leak sealer... Over christmas as she had a pin hole in towel rail.
Called me out for other bits and mentioned this I went in to loft and looked on F&E and it's is only about an inch over tank connector and has...
Does anyone know if you can buy an adaptor to fit on the unions of the worcester filter so you can connect magnaclense power flush machine connections ?
Hi guys. I hope you are well. Does anyone know what size hole it is for this button connecton? Actually, what I am trying to say is can this be replaced with a fluidmaster?
Thanks
Can anybody advise what size fittings are needed to connect this to the flush pipe?
https://www.diy.com/departments/flomasta-dual-flush-fill-valve-kit/3663602452232_BQ.prd
I'm in the process of trying to replace a leaking flush valve with a Flomasta Dual flush Fill valve kit. The problem I've got is trying to get the flush pipe connected into the base of the valve. The existing flush pipe is marginally too small, but might be OK with a suitable gasket but I'm not...
Hi
I am after a couple of parts for my double flush toilet
Firstly the buttons (see pic below). I order some but it did not have the central screw as show in my image below. Anyone have a link for somewhere on Amazon (or the alike) where I can get this please? Chrome in colour.
Also, I have...
SO, I have done about 30 of these and they all have the same problem... the old seal had become so conformed and imbedded in the base that the seal was so great that you would break the handle trying to flush. So its time to replace, the new seal is straight and flat and not conformed at all and...
Need help?
So just been told by my plumber that it looks like my unvented got water tank, Santon 300 litres is lime scaled up causing the pressure to be getting lower on the hot water.
Are there any plumbers or companies out there that can do a descale and flush through or otherwise I need...
Hi , hoping someone may be able to advise - seems like this should be easy...
Came home to find that my wife had had a problem with the push button on toilet (sticking). She had taken it apart as below. I understand that the button should push down where I've drawn an arrow and the cable...
I have been called in to sort a friend's heating system. They were constantly bleeding some of the radiators! The plumbing is a bit of a nightmare, done by the owner but cut and changed over the years. Originally there was a backboiler heating the system, this was removed and an oil boiler added...
Hi,
a new member here, so first of all, hello to the forum!
Posting because - I've got a couple of problems in a relatively new bathroom installation. First issue is - the bath drains very, very slowly (and backs up slightly when the shower is in use). The second is, the toilet flush is not...
Hi
Our toilet bowl is constantly filling after flushing.
I've looked on the internet and youtube and couldn't see anything like the cistern we have (I'm no DIYer by any means)
I've attached a picture, cousl anybody point me in the right direction? I've tried to change the height of the white...
Thermal Solar
I have installed the above in my 3 bed simi
with22mm pipe and an E and WEst panels into a cylinder with solar h/E and boiler H/e above .
Is there and DIY way ( am not a proffesional) of filling and flushing , without buying and expensive fll and flush station please ?
I used a...
Hi.
Wondering if anyone could help me. I've had my WC sitting like this for a year now. After having this fitted while I was at work I'd purchased a toilet with cistern and thought the flat flush Valve I'd ordered seperately would fit it but it never. So Ieft with the gap for a flat flush...
The old Dudley type - long flush press and hold, short flush press and release.
I can't get one anywhere they all seem to be the opposite way around - stand there holding the lever and looking into space for the short flush ! (which we all do more often) and press and run off for full flush...
The push button on the wall for my toilet no longer works. It pushes in but does not flush the toilet. I can flush manually by pushing down in the cistern - photo attached. I have checked the tube from the button leading to this and there does not appear to be holes.
Anyone know what the fix may...
Hi, would anyone be able to identify the make/model of this dual flush valve? It has no identifying numbers on it at all, however the separate fill unit has some numbers that might help someone in the know. It would be greatly appreciated, thanks
Hi,
I have a newly installed toilet but the flush only pushes water around half of the toilet bowl, no water gets to the front. Is the an issue with the toilet, cistern or pressure (water pressure in house is good)? And how can I get this issue fixed?
Many thanks
In 95% of instances the much cheaper/simpler Magnacleanse type filters seem to be really effective. You obviously need a working circulating pump but has anyone used one where a boiler couldn't generate hot water?
Do people still buy powered units? I had planned to buy one but haven't really...
Hi,
We have been having issues with our toilet flush for some time. Lots of times it does not work in the first or even the second go and flushing the toilet releases a small amount of water. When we let it fill up again(second or third go) and then try and flush, it releases all the water and...