went to look at one of these today,what a total heap does anyone fit them looks a nightmare to work on,turns out it was out of water,f9 flagged up whats the crack with a digi WP gauge? do i need gaskets or a big hammer to service it?
Hi got a Glowworm combi there hot water luke warm untill you turn the tap right down them it gets hot, thermostats workin as when i turn it up it gets hot then when i turn it down it gets colder but you cannot get hot water when the tap is on full, cold pressure to the boiler is 3 bar, anyone...
Why, when following the fault finding guide in the M/I's of a Micron 40FF does it suggest checking 6 LED's when the board appears to only have 2 LED's? I think the lights illuminate in conjunction with the ignition sequence.
Why, when following the fault finding guide in the M/I's of a Micron 40FF does it suggest checking 6 LED's when the board appears to only have 2 LED's? I think the lights illuminate in conjunction with the ignition sequence.
Greetings all.
Called my plumber out 2 weeks ago to fix my boiler and a radiator that was cold. He couldnt find anything wrong with the boiler so just did a service on it as best he could. He also fixed the radiator.
The fault I have, which is kind of intermittent, I'd say 80% it doesnt run...
Had a call tonight regarding the fault code "F9". It relates to the system pressure and only seems to cause a problem with hot water that we know of. Sometimes it resets straight away and othertimes it takes a few attempts. Any ideas?
I can confirm the pressure is correct (according to the...
been to another of these where the filling loop valves are passing and the boiler pressures its self up to mains water pressure .this is the 3rd in the past 6 months .the valves and the filling loop pipe amount to £185 this is mad . last one i capped the flexi and one side of the valve and...
Central heating only fires fir 10 seconds no lockout hot water ok. Divertor valve and motor ok pump ok. Rads get luke warm.
Sludge? But wouldn't it lock out?
About time this 35 year old bit of junk went to the scrapheap; but anyone know where the spillage should be carried out on the fire?
No mention of it in MI's, so I assume it's at radiant canopy?
Our boiler is just over 3 years old. Last winter it had a recurring problem with loss of pressure - we kept having to re-pressurise it to get the CH to work. The hot water worked fine until the system asked for CH (either when the thermostat/timer kicked in in the morning or we switched it on...
My Glow Worm 24CXi timer still rotates and displays the correct time but now the heating is not triggered by the the programmer. The boiler works as normal when you manually select the heating to come on and fires as normal when there is a demand for hot water.
It used to click when reaching...
fitted a betacom 28a about 5 months ago and got called back to it today due to poor ho****er - checked at taps only 39degrees with tap on full flow or low flow . water temp set at 60 - 14 degres across plate - flow 73 rtn 56 on boiler . checked fan target and actual values which were ok . inlet...
Hi guys, my boiler's down to 0.4-0.6 at the moment, how on Earth do I fill the CH? I've tried turning most knobs with no joy! :D
Here's a photo:
Many thanks!!!
:hand:
Normally all ok but past 2 days will not always start up on its own. The fan comes on, click click spark ignition and pilot lights then main burner set. Past two days unreliable but all will go with a lit blowlamp stuck in viewing hole.
Anyway took it all down this am and nothin obvious...
I've been to have a quick look at my mate's boiler and its displaying F.12 which is 'Connection fault between main pcb and display pcb'. The boiler is not firing up. The wire itself seems ok, no obvious breaks/damage (have not actually tested yet). I've had a word with a couple of people and...