ideal | Page 9

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

ideal

  1. G

    Ideal Esprit HE 24 Combi

    Is not working and cuts out with an L9 code. Will not start again for some time until the heat exchanger cools, which is a good while. Will fire up if left alone, pressure gauge fluctuates wildly before cutting out. It is overheating on the heat exchanger? Manual is indicating a thermistor...
  2. C

    Ideal Isar HE30 no heating

    Morning all, just want to get an idea of the problem before I call engineer. Have been ripped off in the past, so.... Hot water absolutely fine. First time I’ve turned CH on this year, it makes all the right noises as though on, display shows ‘c’, pressure fine, but the rads still stone cold...
  3. B

    Ideal Classic - is there something wrong with the flame?

    Hi, my first post. I have an Ideal Classic FF230 which has been noisy for a while but recently has gone a little quiet. It used to make a noise which seemed like the fan was going but that seems to have gone. Now the burner shows a mix of orange with the blue flame and there seems to be red...
  4. G

    Noisey ideal logic combi

    Hi , I’ve got an ideal logic making a humming noise . Has anyone got any experience of this ? Thanks in advance. Greg
  5. trickyguns

    Ideal Vulcan SX / DLX gravity fed boiler - No hot water

    HI everyone, I went to look at a prehistoric gravity fed Ideal Vulcan SX / DLX boiler with reports of no heating or hot water. This is a 4 pipe 28mm pump fed heating and gravity fed water pipes to water cylinder. I found that the heating pump had stopped spinning and found sludge behind the...
  6. F

    Ideal Isar HE30 Condensate Trap

    Hi all, Got home today and the dreaded Ideal Isar boiler had stopped working on me. Error L:F flashing on the control panel Took the front off and noticed a small trickle of water dripping around a small copper pipe on the left hand side According to a few things that I've seen online the...
  7. CorgiDirect

    Best Prices on top, Ideal, Vaillant, Glow Worm, Heating Spares

    We have introduced a range of top heating spares from select manufacturers , Take a look here Heating Spares - CorgiDirect - https://www.corgi-direct.com/heating-spares-17866-0000
  8. S

    Ideal Mini 28 Replacement Boiler

    Hello Everyone, I've just joined and am trying to help a damsel in distress - in very remote area of West Scotland. I'm hoping someone can help me here. Her 17 year old Ideal Mini 28 combi boiler has stopped working. She's had someone round to look and has been told she needs a new boiler...
  9. M

    Ideal boiler displaying F1 error but pressure is as should be

    My boiler is displaying the F1 error meaning I have no hot water or heating. A quick google search tells me that this error is caused by low pressure and theres many tutorials on increasing the pressure. However, my problem is that the pressure guage is telling me the boiler is at ideal pressure...
  10. J

    Ideal Logic System S24IE

    This boiler was flooded through the condense drain which was connected to a gutter downpipe that was blocked at the end. The people came home to a flooded kitchen. Water came back up the condense tru the trap up the heat exchanger and out tru the fan and gas valve connection imside the casing...
  11. G

    HA fault on ideal isar 24he.

    Replaced a main heat ex today for a customer on an ideal isar, heating is ok but when running hot water it overheats and comes up with HA fault code, only happens on hot water though. Any way to shift the air from the plate heat ex? Its situated flat in these boilers instead of the usual on its...
  12. D

    I have a F1 fault code on my ideal boiler, the pressure is fine?

    Pressure is ok but increased to see if boiler would click into action but didn’t, have reduced back, needle is moving on pressure gauge, have tried reset but still nothing, any ideas before I call someone out? Thanks
  13. J

    Ideal Standard moments seat

    Having replaced the soft close seat on this suite twice,(which are not cheap), plus the soft close hinges, does anyone know of a viable alternative soft close seat that looks good on it. Many thanks. Dave
  14. soother

    Ideal logic primary heat exchanger leak sealant success?

    A mate tells me he cured a heat engine leak on this boiler (confirmed by boiler isolation & dripping condensate drain) by adding K-Seal car type sealant, and It's still ok after 5 years. Has anyone else had success curing these leaks with sealant additives?
  15. S

    URGENT Ideal logic losing water!

    Ideal Combi bolier. When I repressurise the system to 1bar it almost immediately dumps the water out the condensate pipe before even switching in on at mains. HELP!
  16. G

    ideal straight swap for the potterton suprima to run a gledhill Boilermate 2000 ?

    I have a potterton suprima 50l running a gledhill Boilermate 2000 job on at the minute. the potterton failed its CPA test with a ratio of 0.1205 and its kicking out a terrible odour. the customers opted for a replacement but I'm a lil stumped on ideal straight swaps. ideally I'd of opted for...
  17. F

    Ideal Combi hot water but noi heating

    Hi all. Daughter's boiler again thanks for help last year. New problem - hot water works fine, but when calls for heat boiler starts and runs for a few seconds then stops. No error messages. My thought is that pump is inop, so boiler starts up but then switches off when the small amount of...
  18. Y

    Ideal Isar HE35 Making Clicking and Clunking noise on Startup

    Hi, I have kept this piece of rubbish going for quite a long time and I don't like the idea of getting defeated by it! Every year there is something new to tackle and replace. I will eventually replace it for a real one! I have now got a problem that I can't work out and was wondering if some...
  19. T

    Ideal Logic+heat 24 (not combi)

    Hi I have an Ideal Logic+heat 24 (Not Combi) it is: Alternatly flashing between: 0 (on its own) and C (on its own) when in central heating mode, it works fine on water only, any idea as to the fault? many thanks Tom
  20. WaterWorks420

    Ideal Logic Combi ES38 No control

    Hello, I have a Logic Combi ES38 Boiler and for some reason, it's ignoring the commands from the thermostats on the wall, for example, both thermostats are set to off but yet the boiler is still on, I've tried the following: I've turned it to just water and not radiators no effect. Changed the...
Back
Top