logic | Page 10

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

logic

Recent contents Top users
  1. R

    Ideal logic plus 24kw flame loss

    Evening all Went to this boiler today reset it then checked it with the fga gas working pressure with hob also running cleaned electrodes made sure the flue was clear emptied condie trap water pressure cleaned out the sprio filter gets home customer calls again boilers displaying same...
  2. G

    Ideal Isar pressure gauge on an Ideal Logic...

    Hi, has anyone used an Isar pressure gauge on a Logic? Spoke to my local plumbers merchant and the bloke said the local council do this when they can't source parts for the Logic. The part numbers are different but he seems to think they're compatible. Asked Ideal and they just stuck to...
  3. S

    F1 fault code on a Ideal Logic combi 24 boiler

    So a f1 fault code appeared today on my boiler and I looked in the manual which said it was a pressure problem. I reapplied the pressure so the gauge read 1.5 and then bleed the radiators. The pressure originally read 1.2 There was a lot of air in them which drained the pressure gauge close to...
    • scrappydez
    • Thread
    • boiler combi fault ideal ideal logic logic
    • Replies: 2
    • Forum: Boilers
  4. B

    kids logic

    just brought a expansion vessel in from the van to check its the right one for a job mid week,its for a 105 in a baxi box,my 11 year old daughter asks what is it dad.looks like a pizza box,so shows her the vessel and explains what it does,now we have a potteron performa condenser ,so she knows...
  5. 6

    Ideal Logic 35+ Combi HW Flow Problem-Airlock?

    Basically after fitting new pvc piping to old 22mm copper there seems to be little/no flow from the hot water tap after reconnection and it appears to be brownish water for first second or so? New to the forum so HELLO :) Detail: For plumbing new bathroom I needed an extra T for hot and cold...
  6. D

    Ideal logic no hot water

    just wondered if any damage to the flow sensor could take out the pcb on an Ideal Logic. Can anyone advise please.
    • dawgas
    • Thread
    • hot water ideal ideal logic logic water
    • Replies: 5
    • Forum: Bathroom Advice
  7. Riley

    Is my logic reasonable here

    Evening gents I have been unfortunate enough to pick up a job from where a builder has scarpered when he couldn't get any of the plumbing to work. I thought I had it all licked but today the customer has come back to me telling me that the new thermostatic mixer bar is only coming out...
  8. C

    ideal logic heat 24 not firing

    Am in need of some advice please. My boiler stopped working 10 days ago showing error code fd (no flow), new flow sensor, pump, pcb, a power flush, 3 plumbers & £600 later we're still at fd and boiler not firing up past 4 seconds. Even speaking to ideal they're scratching their heads. Its...
  9. C

    Ideal logic / indenpent L2 fault code

    Have L2 lock out on a logic, anyone who work on these have any common causes of L2 on them doesn't even try to fire up then lock out as far as the customer says? thanks in advance :)
  10. A

    Ideal Logic gauges

    Serviced 3 Logic+'s today, two of which when the heating is running or the pump over run is on after demand, the pressure gauge needle is rattling about so much it is actually noticeable from within a 3m range from the boiler. Luckily ones in a cupboard so that drowns out the rattle, but the...
  11. C

    ideal logic heat 24 not playing ball

    Heat & hot water stopped 2 days ago, boiler flashing fd. Followed trouble shooting in manual and ordered a new water flow sensor. Was replaced today, still no blue light and still flashing fd. New plumber called, he replaced pump and told us to bleed rads and all will be fine. 5 hours later...
  12. E

    Ideal logic heat 15

    Went to service logic heat 15 today with complaint of L2 showing and having to reset to get it going . Hadn't been serviced in five years from new ... The heat exchanger and siphon were gunged up with aluminium oxide sediment , cleaned thoroughly., cleaned spark and sensor probes ,checked flow...
  13. C

    Ideal Logic Combi 35 F-1 error with pressure on gauge

    Hi all, New to the forum. Last night, while running hot water from our Logic Combi 35 boiler the front display started displaying F-1 and stopped producing any hot water. Of course this usually means low pressure, however the gauge is showing 2.5Bar. There is plenty of pressure at the hot...
  14. A

    Ideal logic gas valve

    Can the ideal logic gas valves be adjusted? Couldn't see anything in the manual. I've got one to go to that's making a baffling noise.
Back
Top