shower | Page 8

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

shower

  1. D

    No hot water coming out when tap turned on in shower

    Hi all, I have an issue with our shower's hot water. The shower is operated using two separate taps for cold and hot water. When the hot water tap is turned on, no water at all comes from the shower head - not even a drizzle. However, when the cold water is turned on it flows freely. The hot...
  2. K

    Is this pipework correct for a shower

    We are having a shower fitted and the pipework in our loft looks very fragile, is this correct?
  3. R

    Replace Aqualisa power shower to mixer shower

    Hi - I want to replace Aqualisa power shower to mixer shower to a std. mixer shower, however, the centres for the hot and cold are only 65mm. I’ve tried finding something that would be compatible but no joy. Ideal would be a mixer head with the same centres. Does anyone have any idea as to...
  4. L

    Lost fixings for hinged bath shower screen

    Good morning, I have a hinged shower screen for my bath that I don't have fixings for. The guide holes in the screen line up with guide holes in the frame - but the holes in the frame are horizontal slots, presumably so that I can adjust the shower screen for a not-quite-vertical wall. However...
  5. C

    Fixing loose shower drain

    Hello, I am concerned about the shower drain body in this picture being loose. I can move the metal ring visible in the picture left and right freely with my hand. My question is whether there is way to fix this from above without having to access the drainassembly from below the shower tray...
  6. M

    is it possible to change shower cartridge rather than the whole valve

    i currently have a valve/cartridge that controls only temperature is you turn it one way or the other. is it possible to remove the cartridge to replace it with one that can control both volume and flow rate? it may be about 30 years old/original to home. everything is accessible as i am...
  7. C

    DIY shower with exposed pipework

    Hi everyone. I'm installing a walk in shower, opening into shower will be on right, mixer value on right, but shower head and drain on left. The pipe work from the shower mixer valve is exposed silver colour pipework. the pipe work will run up from the valve then take a hard left at the ceiling...
  8. B

    electric shower vs. mains from dual cylinder submersion heater

    Hello, and thank you for reading. My partner and I have just purchased our first property that came with a dual cylinder electric water heater, and an electric shower in the bathroom. As it happens, the shower needs replacement, and we were thinking of removing the electric shower (Mira Sport)...
  9. S

    Shower issue with two new showers

    Hi all, can someone get to the bottom of this before I call a plumber, en suite shower started leaking from the mixer bar so took the shower off and capped it off for the time being, fast forward 3 months the same thing in the main bathroom, that one is leaking from the mixer bar, (no issues...
  10. Crossfingers

    Electric shower takes while to cool

    I have a strange problem with my Mira Sport electric shower. When I first turn it on its hot, even at the coldest setting. I have to let it run for a while, hear a thunk from the pipes under the floorboards and the cooler water comes with a bit more pressure. Seems toe it's not full pressure at...
  11. S

    Fitting 900mm shower door in 915mm space between walls

    I live in the UK and I need to buy a shower door to fit in a 915mm gap between two walls of my shower room. Most 900mm shower doors available here have 30-to-40mm inward adjustments to fit in a space that is slightly narrower than 900mm, or to address wall unevenness, but not outward...
  12. J

    Adding shower waste to horizontal 110mm pipe

    Good afternoon, please see my attached diagrams One is the current layout And one is where I propose to add another boss to add a shower waste. This horizontal run is below floorboards but I can't get to the TEE or under the tee to add a boss vertically. ( the current Bath is bossed way in...
  13. G

    Milano Baya Shower Tower

    Morning gents and gals, I have a Milano Tower Shower about 15 years old, where I have a couple of issues :- 1. The shower head has seen better days and I would like to replace it, however, the BPS seems to be a 1 inch or so not the usual 1/2 inch and the grey fitting at the top does not want...
  14. Inverness

    Shower waste problem

    New house and smells comes from shower... It's a merlyn shower waste it's not like your usual design. I've lifted up the chrome but or I'm I suppose to lift up the other bit to get the hair bucket removal out? This design I don't see where the seal is to stop smells through?? Any experience...
  15. Stuartpm

    Straight valve to turn shower on & off (you'd think this would exist)

    Hi - recognise this a bit of an odd one. We have an old failed mixer valve which we need to replace. This valve actually predates a temperature controlled boiler, so the mixing functionality is irrelevant, since the cold water pipe is isolated/off. I'd ideally like to replace the shower valve...
  16. Stants

    Connecting Grohe shower using adapters to 15 mm supply

    Hi I've purchased a GROHE | Euphoria 260 Exposed Shower ( looks nice ) however Im missing some initial connecting adapters the installation instructions say it comes with " easy install adapters " and threaded tape ....I have neither of these ,all I have is the " S " unions ... so I did a bit of...
  17. E

    Advice on shower tower fittings

    Hi, I have a shower tower fitted and my flexi pipes (500mm) are about 7cm short of where they need to be to fit onto the mixing valve in the back of the shower. I cannot move the shower up and the next longest flexi pipe I can find is 900mm, which is about 830mm longer than I need.. Would a 15mm...
  18. D

    Void under shower tray former

    Void under shower former My recently installed solid resin shower tray / wet room former has around 4mm flex across a dinner plate sized area in the middle. It's on a concrete base that was unevenly screeded over. The gap will likely be under 10mm. It has not yet been tanked or tiled but would...
  19. T

    Thermostatic shower valve

    I am redoing my bathroom and not sure what the best way of doing my shower is which is in my bath, I want a rain shower and so I was thinking of using a thermostatic shower valve as I have removed the plasterboard to re tile (new build) and thought this is a good opportunity to do it, my...
  20. T

    How to remove this kind of shower mixer?

    Hi all, I'm trying to remove this shower mixer however, I cannot see any bolts like all the other ones I see online. Please can someone advise. I've taken a picture of it: Screenshot - https://prnt.sc/YS6WnqriFxHP
Back
Top