size | Page 2

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

size

Recent contents Top users
  1. O

    Shower size help/advice (DIY)

    Hi all Fitted a new shower at home and the shower arm extends too far out for the screen (pics attached) a lot of water escapes out of the shower and on to the floor. Is there a replaceable shower arm that I can purchase and if so what should I search to find this? Or is just a case of buying a...
  2. O

    What size air filter?

    Hi all, Just bought a new place that has a heat pump model # AHV42D3XH21CC I can not locate an owner manual online anywhere and wondering if anyone else can help. The previous owner also had a 20x23x1 air filter in it but I can not locate these? Was this the correct filter size as this does...
  3. C

    Boiler Type and Size

    I am looking to put a new heating system in a 5-6 bed house with 4 baths. The config is as follows: Upstairs there are 2 beds and 2 bath Downstairs there are 3 beds and 2 bath + Kitchen + Utility The max usage bathrooms wise will be 2 showers running in parallel. Total radiators will be...
    • Capricorn
    • Thread
    • boiler size
    • Replies: 1
    • Forum: Boilers
  4. J

    Reconfiguring Ideal boiler PCB to correct model and size

    Hello, I am trying to get my Ideal Logic Heat H15 repaired. There have been various faults appearing, with most of them pointing to the PCB. It has been decided that the best option is to try replacing the PCB and using a refurbished part initially for testing. The PCB used on the Heat model is...
  5. W

    What radiator size please?

    The recommended radiator size for my bathroom is 2500BTU. The rad. I have chosen is available in 2258 BTU and 2741 BTU. The smaller one will fit better but I would not want to compromise the heat output by choosing it just because it looks better in place. Bathroom size is 7' x10' x8' high with...
  6. J

    Vent pipe size for vented cylinder installed in 2005-6

    Hey, having searched this forum and last building regs (2000) from around that time... Any idea what the correct size is for a vent pipe for a vented hot water cylinder, gravity fed? I.e. the one that is continuously rising back up to the cold water feed tank for the cylinder? Have discovered...
  7. A

    Pipe size length bends junctions to Combi - affect on water flow rate?

    Hello! Advice required, please. Trying to understand implications of pipe size, length of run, and number of junctions etc. en route between the incoming water feed to the Combi-boiler. For various reasons it is difficult to get from stopcock to boiler without taking indirect route back across...
  8. A

    URGENT Heating pipework size

    I am doing a 3 garage conversion into a annexe. I am doing it all in push fit plastic. I don't want to have any joints in the ceiling to minimize any chance of leaks damaging at any point in the future. My question is can I run from the boiler each individual radiator off a mainifold. Pipes...
    • Andy Griffith
    • Thread
    • heating pipework size
    • Replies: 1
    • Forum: Bathroom Advice
  9. V

    What size is the small connector on the valiant 837 filling loop?

    Hi Guys, The valves on both sides of my Valiant 837 filling loop are letting through causing a constant pressure rise (seems to be a common problem). I want to cap off or isolate the small connector but its not a size I recognise, the part number for the filling loop is 0020010293. Can someone...
  10. S

    What size boiler needed

    Hi there Could someone please advise what size condensing boiler I would need to run the following all at once. 225m2 of underfloor heating ( calculates on length x width of rooms) 8 Rads at 1470 watts each 2 Rads at 1.176 watts each 4 Towel Rails at 200 each watts DHW at 3000 watts...
  11. Scott_D

    Hole size for kitchen tap

    Would anyone know what the hole size is that a standard kitchen mixer tap requires?
  12. N

    What size combi for my daughters house.

    Hi all....my first post.....talked my daughter into seeing about a new modern gas boiler to replace to very old one she has now. Its the type that has a separate electric water heater....parts are very hard to find for it. She has had a few prices and one guy said she needs a Worcester 32Cdi...
  13. omendata

    Flush valve washer needed - nobody seems to supply this size

    Lecica Toilet is quite old (+15 years) I phoned the manufacturer but they sent me a standard washer for the Lecica Cistern flush Valve but it does not fit! Dimensions for the one i require are:- Inside diameter: 75mm. Outside diameter: 57mm.
  14. M

    Non-Standard Tap Washer Size

    I have gone to replace the washer in the shower taps as the shower is dripping but the washer seems to be a non-standard size. The 12mm was too long and so I went and bought a plastic one I could cut the end off but it is also slightly too wide, the 10mm doesn't fit either. It is a really old...
  15. S

    Kitchen Tap Replacement - Nut Size and Adapter

    Hi, I wonder if someone can help - does anyone know the size of this nut/joint and if it will be compatible with the following kitchen tap once I've removed the old one? It seems to have 1/2 and 3/8 Inch Adaptors - will it be a case of unscrewing/removing the the existing pipe and then...
  16. IanNotaPlumber

    Are shower doors less than size stated?

    Hi, I'm not a plumber but just need some advice. I've installed a square shower tray in a recess. Walls on both sides. The tray is 900mm wide. I have tiled the area and now the width between the two walls is around 870mm. Obviously there are no shower doors this size. On Victoria Plumbing it...
  17. T

    What size thread for Immersion Heating Element?

    Hi, I want to fit an immersion heating element to my hot water tank (water is currently heated by gas). I'd like to buy it before I start draining water from the tank. The plug in the tank has a 1 1/4" nut on a pate approx 3" in diameter, does anybody know what size thread the tank will have...
    • Tony Griffin
    • Thread
    • heating immersion size
    • Replies: 2
    • Forum: UK Plumbers Forums
  18. Z

    Syphon size question

    We’ve recently moved house and the downstairs toilet flush has packed up. I think the syphon looks too big for the cistern with the linkages to the handle all bodged with various bits of wire to make it work. Is there a way I can check the size of syphon that’s correct for the cistern?
  19. G

    Radiator size and return to boiler temperature

    Afternoon, Recently had a new boiler fitted with new radiators, old radiators were the old steel type. The installer recommended reducing the size as the new panels are more efficient, which we were happy to do. Now, I believe that for the output of the boiler the radiators are too small/not...
    • garden4ork
    • Thread
    • boiler radiator return size
    • Replies: 8
    • Forum: Boilers
  20. A

    What size radiator tails are these?

    Hi I live in a new build does anyone know what size radiator tails these are? And where I can get the same ones from? Thanks :)
Back
Top