Hi. I need a new toilet supply line but don’t know the size type of the fitting at the shut off valve. It is not 3/8 compression. It is a plastic nut about the same size as the one going into the cistern but has a different thread. Attached is a photo. Can you advise. Thanks.
Can anyone recommend a toilet, sink plunger.
It’s not something I do a lot of, but it will be handy to carry on the van, for when needed.
Don’t want to spend a fortune, yet I don’t want something that breaks after a few uses.
Thanks in advamce
Paul
Hello, I have a question on flush pressure.
When I press the bigger button, there's hardly a flush. I understand that's normal but it's a very minimal flush. And then the smaller button is quite hard to press and I think doesn't do a full flush either. So when I flush I press both and it works...
Hello! We have a wobbly toilet seat… it’s a back to wall toilet and whilst one fixing is secure the other is not, and it looks like the fitter didn’t really attach it all. How do I go about fixing this please! The seat in question is from Qualitex.
Hello, as the title, the cistern keeps filling.
The fill valve is passing, think it’s a viva skylo bottom entry with a plastic shank but there’s not markings or identification on it. Just wondering if anyone knows what type it is?
I’d rather just replace the diaphragm inside if it’s one that’s...
Hi guys, just want to get advice, i want to replace venten to unvented cylinder, is it ok to install D2 pipe to toilet waste pipe see picture? as there is no easy options to get it outside.
With a toilet fit to a concealed cistern vanity were the front panel slides up if you need access it at later date and fitting
Is it advisable to put a small bead of silicone between were the top of the pan sits against the vanity?
60's ranch, with single bathroom. Tile over concrete slab. Toilet is about a foot from exterior brick wall. Vent pipe is in interior wall behind toilet. There's a concrete patio outside the bathroom, that extends about 10 feet from the wall. I'm considering adding an ADU in the back yard, and it...
Hi Everyone
Doers anyone know how to remove this toilet seat? It has no push buttons or caps that I can see and I am trying to fathom out how to tighten it!
Any help appreciated!
I need a new seat for a Bathstore Euro mono back to wall white pan e14. The seat was a euro mono sandwich seat white chr hinge
Bought in 2007. I know that bathstore went bust and homebase bought the old stock. I’ve searched online and found some replacement seats for the euro, but they don’t...
I have an old low gallonage toilet. It flushes fine when when liquid waste is present.
Every time, when there solid waste in the bowl (not a lot) it clogs.
I need to use a plunger each time to get the waste to flush.
I made sure all the holes under the rim are clear.
We have a 1980's toilet and it normaly works by:
1.When flushed the deposit in the bowl is sucked out
2. the bowl fills up again with clean water.
This is not happening now, when flushed the water fills the toilet bowl then emptys and refils.
What can I do?
Is it a profesional plumber callout?
A few years ago I installed a wall hung toilet pan in my last house which did not flush well when disposing of waste solids.
The water would rise up to the rim then dissipate and usually required further flushing to complete the disposal.
I don't recall the brand but the wall mounting frame was...
Hi there. I have a Cersanit close coupled toilet which as started leaking between the cistern and the bowl when flushed. I've taken the cistern off and this is what I see. I'm assuming the issue is with the silicon gasket (please see attached photos) but can't seem to find a replacement...
Hi! Totally inexperienced DIY newbie so bear with me for descriptions! Pictures hopefully help.
I’m trying to remove an unused downstairs toilet in our new house. It’s eventually going to be moved to the other side of the house.
The seal around the back of the toilet had failed so I switched...
Hello,
I have a troublesome fixed 15mm copper pipe with isolation valve going to my toilet fill valve. It's too tight for a Flexi hose. Can I use a push fit tap connector instead which will give me more flexibility in fitting?
Hi, I fix what I can around the house myself and have fixed a few toilets but I need help with this one.
This toilet keeps running and stopping, running and stopping, etc. I've cleaned the rubber flapper itself and at the point that it contacts the reservoir, so I don't think it's leaking from...
Hi,
So i have lived in my house for 20+ years, (1990 build) its a detached property, corner plot with various manholes in the garden. In the last year I've noticed i can hear when my neighbor flush their toilet through my downstairs toilet - this is a relatively new thing, so am assuming its...
Hi guys
So a bit of a dilemma
Normal WC Unit height 766mm which is around the average mark.
quite alot of bogs lets say the flush pipe center from floor is 330-340ish.
However I have a comfort height Pan here and the center to the flush pipe from floor is 405MM
So we're looking 65-75mm...