Disaster and stress!

[Fedup]

Hello, any advice would be extremely welcome. This new external boiler only has a tiny spout as a condensate pipe, and the same with a vapour pipe. Am I right that they should go into a drain? I am also not happy with it being butted right up to the conservatory - is there a rule as to distance? ( there is loads of space)
Hopefully some photo's will explain things a little better. Thanks for reading.

 

[lame plumber]

MFIs will detail distances needed for clearance. re the condensate drain off, it needs to go to a drain or soakaway, thats just going to destroy your brickwork in the long term. re the isolating switch, I prefer mine to have some protection, they are water resistant but there are limits and the cable run should be in conduit. All in all not very satisfactory. I prefer a decent concrete base as well not slabs on sand/cement

 

[Fedup]

Thank you LP, should the wiring sit directly onto the hot pipes?

 

[lame plumber]

the cable used should be heat resistant and it is not best practice to lay it over pipework and from the pictures seen, I havent noticed any earth bond cabling to the oil feed pipe , you should have a 10mm yellow/green cable to oil supply but as this an external boiler it may not apply, although Im not sure, I would rather have it earth as when your cable on the pipe work deteriorates over time making the pipework live a decent earth bond would be nice to stop it killing the likes of me servicing your system. worst case scenario here, not always going to happen but!

 

[Fedup]

Thank you lame plumber ( again). There is a green and yellow earth wire, it was attached to the old boiler. However, the end of it has been chopped off, so it isn't connected. The workmen managed to blow up two showers, there hasn't been any 'making good' in the holes in the walls, I have one soaked carpet, with rust stains, from a leak. So hope you can understand the distress!

 

[lame plumber]

nasty, but cheer up 2nd half and england lead 6-0

 

[Fedup]

nasty, but cheer up 2nd half and england lead 6-0

:grin: :grin:

 

[Irish]

nasty, but cheer up 2nd half and england lead 6-0

Not anymore !!

 

[Fedup]

So this copper wire isn't an earth wire? Is ok to pull it to see if it's attached?

 

[lame plumber]

Not anymore !!

No 12-6

 

[Dotty]

No no no!

That's your fire valve remote phial.

Break that you'll have no heat!

 

[Billy Bob Bob]

so this copper wire isn't an earth wire? Is ok to pull it to see if it's attached? View attachment 10847

no dont pull that its a fire valve

 

[Billy Bob Bob]

THAT IS ONE ROUGH OIL BOILER INSTALL,installer should be shot

 

[lame plumber]

cant see clearly but is that a 90degree or 65 degree firevalve

 

[Fedup]

So this is a fire valve ( very old one that was for the oil AGA ) now connected to a tiger loop? Where will I find the yellow and green earth wire?

 

[SimonG]

I've seen worse but it's not good. Cables should be sleeved, pipes should be insulated, condensate to drain or soakaway, boiler too close to wall (the expansion vessel is at the back of these and you'll never get at it), hole through wall should have been closed up etc etc etc.

Couple of questions for op.
1. Where's the tank in relation to oil boiler? I find tiger loops are generally fitted by people who don't know what they are doing.
2. How far from boiler is the fire valve?
3. Have you had the building control certificate from your local council for the installation?
4. How many quotes/estimates did you get for the install? Did you use the cheapest? Did you ask to see previous work?

 

[SimonG]

cant see clearly but is that a 90degree or 65 degree firevalve

90 degree LP

 

[SimonG]

So this is a fire valve ( very old one that was for the oil AGA ) now connected to a tiger loop? Where will I find the yellow and green earth wire?View attachment 10848

You probably won't find an earth cable. If the oil is only going to the external boiler then it is no longer an incoming service so shouldn't need it. Or so the electrician I use tells me.

 

[lame plumber]

if you cant see it it aint there. if your fire valve now rests in your new boiler its the wrong spec, but better than none

 

[lame plumber]

You probably won't find an earth cable. If the oil is only going to the external boiler then it is no longer an incoming service so shouldn't need it. Or so the electrician I use tells me.

thought that might be the case, but its nice to have a good earth if your the muppet touching things!!

re tiger loop, I keep getting told they are good to use even when not req as they reduce air in oil line and prevent pumps cavitating and wearing out. Not sure on that one but dont fit unless height issues involved.

 

[SimonG]

thought that might be the case, but its nice to have a good earth if your the muppet touching things!!

re tiger loop, I keep getting told they are good to use even when not req as they reduce air in oil line and prevent pumps cavitating and wearing out. Not sure on that one but dont fit unless height issues involved.

He bonds the htg f & r, hot and cold pipes as they enter.

The tiger loop will reduce the wear on a pump if it's near it's limits. But I generally find them fitted when not required because the installer doesn't even understand the use of them. Took one out last year. Bunded oil tank by front gate, garden dropped down a few feet and an old worcester heatslave in the utility room. Burner was probably two foot below bottom of oil tank.

 

[Irish]

No 12-6

Knew I shoulda said nothing! Think ye will do the grand slam this year

 

[lame plumber]

He bonds the htg f & r, hot and cold pipes as they enter.

The tiger loop will reduce the wear on a pump if it's near it's limits. But I generally find them fitted when not required because the installer doesn't even understand the use of them. Took one out last year. Bunded oil tank by front gate, garden dropped down a few feet and an old worcester heatslave in the utility room. Burner was probably two foot below bottom of oil tank.

thought as much re tg loop, re bonding, 4mm supplementary bond isnt really the same as a 10mm earth bond, esp with a external boiler, I like to think I wont be jigging it if cables split esp on an install such as this! no offense to op

 

[Fedup]

I've seen worse but it's not good. Cables should be sleeved, pipes should be insulated, condensate to drain or soakaway, boiler too close to wall (the expansion vessel is at the back of these and you'll never get at it), hole through wall should have been closed up etc etc etc.

Couple of questions for op.
1. Where's the tank in relation to oil boiler? I find tiger loops are generally fitted by people who don't know what they are doing.
2. How far from boiler is the fire valve?
3. Have you had the building control certificate from your local council for the installation?
4. How many quotes/estimates did you get for the install? Did you use the cheapest? Did you ask to see previous work?

1. The tank is about 30 feet away.
2. 26 inches away, and about 23 inches from the vapour release spout.
3. No, do I need one?
4. I had 3 quotes, this was for new combi boiler, so the old tanks had to be removed. £3,980!

 

[lame plumber]

Knew I shoulda said nothing! Think ye will do the grand slam this year

still got an excuse to celebrate with that new baby