Plumbing Jobs | The Job-board | Pro & DIY - | Page 103 | - Plumbing Advice Forum > PlumbersForums.net

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Questions and plumbing advice in the Plumbing Jobs | The Job-board - .
Normal Threads
Hi All I’ve opted for a Vokera i36 with at a bargain and a 7 warranty. I’ve a wired Heatmiser...
Replies
3
Views
1K
Hi folks, I have to replace a Valliant vrt 230 stat/programmer. Can you advise a direct...
Replies
7
Views
2K
I moved into my new home last year and had a new stopcock installed last Oct to replace the...
Replies
22
Views
19K
My heating pump was installed by BG with the motor shaft at a 45 degree angle. Could that...
Replies
11
Views
2K
hi everyone, been doing a fair bit of work and hit a little problem, when pushing the boiler...
Replies
10
Views
2K
Hey folks, got a weird one here. CH system has been isolated and is not dropping ( gas test...
Replies
24
Views
3K
Glowworm 100ff wall hung 30kw conventional boiler. Set up in garage with correct 28mm runs to...
2
Replies
25
Views
3K
Is it ok to use push fit connections on old 1/2 copper. I know you need adaptors for 3/4 to...
Replies
9
Views
1K
Any of you come across this problem something is not right here ? Cheers kop
2
Replies
26
Views
263
  • Redirect
Hello! I am new to the use of oil based boilers and seem to be having a problem with the...
  • Scott Lewis
  • N/A
Replies
Views
N/A
Can anyone be so kind as to help me out. I've read the instructions for the above thermostat...
Replies
12
Views
10K
Hi looking for some advice thanks in advance, I have got a plumber coming over to check this...
Replies
4
Views
1K
Leaking from pan spigot to pan connector connection. Someone has siliconed this joint before...
Replies
12
Views
155
Hi all. New member here (English expat living in Canada) - thanks for having me! We had our...
Replies
8
Views
5K
hi all, got a customer who is being driven to despair by a ch pump that is vibrating against a...
Replies
8
Views
86
hi all, dropped the Grundfos 15-50 bleed valve down the floorboards out of reach. The whole...
Replies
19
Views
2K
I've fitted loads of normal sinks but have been asked to fix one that's dropped about an inch...
Replies
11
Views
1K
Hi, Ive been sent this by a customer who has asked me to replace this. What would be quickest...
Replies
11
Views
143
i need to cap this pipe under the floor, will need to remove the elbow and fit a cap. Not sure...
Replies
7
Views
1K
Hi all, My pressure reducing value has failed on my unvented cylinder, my plumber has already...
2
Replies
27
Views
3K
I would be very grateful if someone can give me some advice on the following. I have a...
2
Replies
37
Views
8K
Hello all. I’ve got a problem with 105he driving me mad. When you switch boiler on and set...
Replies
18
Views
267
So my fault finding has gone downhill over the past couple of years ad I haven't been doing...
Replies
0
Views
159
At the base of some cast iron soil pipes? Seen it on a few but not actually sure the reason why.
Replies
9
Views
2K
Nobody ever owns up to doing it
Replies
5
Views
119
Gobbo, check out the posts by this troll and also check your profile page for comments left by it.
2 3 4 5 6
Replies
137
Views
2K
Hopefully this question has a simple answer. I'm looking at monobloc taps for my new kitchen. I...
  • Jake Morris
  • 4
  • 14K
  • Latest:
  • Welder
Replies
4
Views
14K
Welder
W
Have just moved into a property when there is a circuit and dedicated plumbing for dishwasher...
Replies
8
Views
2K
I've just replaced the diverter valve on a Potterton HE (and the motor) and its still leaking...
Replies
18
Views
2K
Hi, Just moved into a new flat. Half of the house has radiators, but the new extension has a...
Replies
8
Views
4K
Post a New Thread / Question

New Threads

Back
Top