Hi all,
I've got 2x AHUs where I work with pre-heat coils after the filter on the supply ducting. These are heated using the boiler CT circuit. On both of these AHUs the method of control of heat to the coil is a 3 port mixing/diverting valve with the central port blanked off. There doesn't...
Hello,
I've just had a regular Ideal boiler (15 yrs ols) removed and replaced with a Vialliant 430 boiler with Nest control. My Boiler is located in my garage but the Nest is in the emersion cupboard. The pump is located in the emersion cupboard. The boiler requires a separate feed from the...
Hi guys
Our recently installed UFH system is causing us trouble and we are struggling to get the fitter to help, problem one is we have to slowly build up the heat as the new floor is tiled but the only way to do this is by turning the boiler heating controls down as low as it goes, 30 degrees...
Hi Guys,
This is my first post, hope you will help me with my questions.
At home I have a megaflow system feeding a downstairs shower and upstairs bathroom. Two issues with the shower control
1) water too hot, rotating the thermostat only increases the temperature :( looks like it has not been...
Hi Forum,
There is a Caleffi Inlet Control Valve (1 piece) connected to the hot water cyclinder and the cold feed, that is periodically (every 5 mins) hissing air, out of the grey catridge, when the hot water is heating.
- I've search around for an explanation without luck.
I don't...
After the success of yesterday's posting, and the constructive support I received I wonder if I could please test the skills of the wise again, as today I've a problem of my own to resolve.
I called out a gas engineer this morning because our boiler, an elderly Ideal Concord CX 240 P, has...
I have recently had a External Worcester Greenstar Heatslave II 18/25 External Combination Boiler Oil ErP installed which is controlled by a salus it 500BM
I understand at the time, there had been a mix up and the incorrect Salus was installed and it should have been the salus it 500 and i only...
Hi,
Having replaced all the radiators in current system I would like to update the control (as seen in image) with a modern digital one. Would this be a simple job and what type of control would I need?
I'm not a complete novice when it comes to electrics but then I'm no electrician either.
All...
Hi,
I have a 2002 installed Vaillant Thermocompact 624 system boiler, 'S' plan with an unvented hot water cylinder, this is currently controlled via Hive.
I have a boiler fund in preperation for when my exiting boiler dies and I'm just exploring my control option wish list which I hope you can...
worcester heatslave exterior boiler. 3 year old.
Oil level in tank is low about 20mm above the Tank outlet.
The tiger loop goes crazy with bubbles when i press the lockout button.
I bleed the oil pump but nothing, even tried oil gauge but nothing? Checked oil filters are fine. I've cracked...
I have a Valliant Thermocompact which is getting on a bit now and I'm looking at getting an ecoTec plus 624 as a replacement.
My current set up is a system boiler with unvented hot water and 'S' plan control via Hive and would like better control i.e independent temperture control of the CH &...
hi. Looking for a Heatmiser Neoair thermostat 4 of them and UH8-RF fitted to exsiting heating system. Current wiring centre is a JGWWC and thermostats are managed by a salus RT500RF. Need finished system to be controlled by iOS devices. Current boiler is glow worm Ultracom. Please message me...
Hi all,
checking on the WB website, it appears to suggest that the Greenstar Ri is not suitable for an upgrade of controls to intelligent/web based..... or is it simply that there are no WB intelligent/web based controls available?
In other words, can Hive/Nest etc be used with this boiler -...
Sat here watching telly and the missus says its ruddy hot in here, so I check the room stat which is making all the right noises, its clicking off but the boiler is still belting it out.
Next I turn off the heating and hot water at the programmer but the boiler is still active.
Finally I turn...
I have a problem with a new installed UFH system as follows.
One 46kW oil boiler heating two number 12 port manifolds plus DHW and rads and I am having difficulty controlling the TMV on both manifolds.
Having set both manifold mixing valves to around 45* the TMVs don't hold that temp.they both...
Have seen this for sale
AXOR hansgrohe Thermostatic Value Shower Control 3 Settings Silver Metal
How do I know if this will work on my shower? We have a very outdated shower from the 80s, with a simple lever mechanism that turns shower water on and adjusts temperature. Will this one listed...
On the front control panel, below the boiler rest button, is a small plastic cover with what appears to be a comms socket behind. This is missing on my friends boiler and they have been told not to use the it. Is this not just a cover or does it really affect the boiler.
Thanks in advance
I have a Halstead condensing boiler in the kitchen supplying HW and heating. There is only one heating zone. I have a heatmeiser thermostat/ controller in the living room. Ive never been able to get a good balance of heating over the whole house. I am now changing all my rads for column types...