flue | Page 8

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

flue

Recent contents Top users
  1. P

    ADVICE PLEASE MINIMUM CLEARANCE ON A COMBI FLUE

    Good Afternoon Please can anyone confirm what the minimum distance the top of the flue pipe should be from the eaves and guttering if the flue is extended so the end of the flue is past the fascia and gutters and releases any gasses into the open air. I have an Intergas 28/24 combi boiler In...
  2. Harvest Fields

    Ferroli F24 Flue problem

    Second opinion boys and girls. How would you class this? Thanks in advance.
  3. CorgiDirect

    FREE Pipe Clamps when you buy a TPI DC710 Flue Gas Analyser

    OFFER 1 Buy a TPI DC710C1 For Only £350 ex vat and receive a FREE Pipe Clamp - https://www.corgi-direct.com/dc710c1-flue-gas-analyser-kit-17953-3423220 … OFFER 2 Buy a TPI DC710C2 Kit For Only £425 ex vat and receive a FREE Pair of Pipe Clamps -...
  4. MikeJhn

    Spare part for an old balanced flue boiler

    Guys Modification of any fuel burning appliance is strictly forbidden unless you have the approval from the original manufacturer If you want more efficient boiler change it don’t start modifying your existing one
    • MikeJhn
    • Thread
    • boiler flue part
    • Replies: 14
    • Forum: Boilers
  5. S

    Flue for old atmospheric boiler

    HI, I had a new gas meter fitted a year ago and the installer said he wasn't happy with the flue. I have lost the report but would like to correct any faults. The boiler is an old Thorn floor mounted atmospheric boiler which is located in the corner of a single story flat roofed garage which...
  6. J

    Reasons for Dripping Flue

    Is there an obvious cause for a dripping flue on a newly installed condensing system boiler? not constantly but enough to form a damp patch on the patio below. Thanks
  7. NODDYNODSVILLE

    Power flue to Balanced flue

    Further to my post earlier today, a change of plan. Is it possible to change a power flue fire with no chimney to a Balanced flue fire? and if so, what is involved
  8. R

    Flue Location.. Is it a Balcony, a Car Port or a Soffitt?

    Hi. I'm new to all this, and not sure it's appropriate, so be gentle with me. This flue is to my newly fitted replacement Ideal Logic Max boiler. The position is the same as it was with my old boiler. I have been told in the past that it was incorrect, but my fitter has assured me it is now OK...
  9. B

    Flue Gas Analyser Calibration.

    Hi Guys, Looking for some advice here. I have two Testo FGA's and they need servicing and calibration. Looking for somewhere that is dependable and competent and not going to cost half an arm.... Thanks in advance....
  10. P

    Must balanced flue inner and outer be the same length?

    Hi. Our builders hit a problem with extending the balanced flue through a new extension. Their solution was to have the outer, intake pipe terminate at an external wall, but add an extra section to the inner pipe to take the exhaust away from the next house. However, the gas boiler was...
  11. C

    flue analysis ..is it servicing?

    Hi all I have been installing boilers and now I'm out servicing different type of boilers. Please a co..co2 reading of 0.0004 to 0.0008 is seen as standard. What about 0.0001 and above 0.0008.? I got the Anton table guide ...does it mean that a boiler flue reading of 0.00013 or up 0.00015 is...
  12. M

    Nearly new Keston combi boiler flue coughing/ejecting hot water & steam

    Hi everyone I would be grateful for advice about possible causes of excessive quantities of water being ejected from my flue. When the boiler switches on in the morning, the flue exit from my apartment block generates a lot of steam and then coughs up glass-amounts of water, falling on the...
  13. C

    Neighbours Flue opinion needed

    Hi there, I'm looking for advise as I'm a little too close to this issue and need an impartial eye. Last year my neighbours installed a new boiler with a flue that terminates vertically at roof level. Initially I wasn't to concerned, but when it started to plume I noticed that it was...
  14. DGT plumbing

    What flue gas analyser should I get?

    Asking opinions, thinking of getting a new gas analyser. Currently have a Anton Sprint V2. It's getting on a bit now and was thinking do I get another Anton as I have already got the accessories or do I get something complete different and if different what do other people use or recommend.
  15. J

    second hand gas flue analyser?

    hi i have just completed my acs qualification and im looking at purchasing a gas flue analyser. as money is tight at the moment i was looking into second hand appliances. the question is if the analyser is still calibrated until december 2019 but has no certificate or a certificate in another...
  16. T

    Boiler flue not accessible but builder says it's all one piece

    Hello everyone. I'm hoping someone can help... We have recently redone our property and there is a new boiler and flue. The flue enters the ceiling above the boiler and is hidden from view (above a bathroom) until it exits through the wall. We have tried to get a gas certificate but the...
  17. R

    Intergas Boilers flue integrity

    Do the newer intergas boilers have air / flue integrity test point on the flue. The last one I got didn't but I was told they were planning to change the design.
  18. K

    Flue Gas Analyser Recommendations

    Hi, what's everyone's thought's on the best quality/value FGA just now? I've had a Anton for the last 6 years but I'm getting to the point where it spends as much time being re-calibrated as it does in my van! Thanks.
  19. CorgiDirect

    Ask the Inventor within this Post (Flueshoe, the number one flue cutting tool)

    Introducing the Flueshoe, the number one flue cutting tool. We are delighted to welcome the inventor, Simon to the forum. He will be on hand to answer any questions you have, about this innovative, time-saving product, that is already saving installers time and money. Simply, ask your...
  20. Jock Spanners

    How do I fix a flue damper in the open position?

    Evening all, I've been to service a gas fire and found it had a flue damper plate which isn't permanently fixed. They only want to keep the gas fire for a short while until they get a wood burner. My question is: how do I fix the damper plate in a 'permanently open position'? Is there a...
Back
Top