high | Page 10

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

high

Recent contents Top users
  1. J

    Kitchen sink waste too high

    Hello, I'm reposting as my post was taken down. I have a double sink in my kitchen that doesn't drain well due to the waste pipe being too high. Before having the waste pipe moved, which will be a mission, I thought I'd look into all options possible. Many thanks.
  2. T

    High flow 440 lpg

    I serviced above boiler today & the negative flue pressure indicated it was due for a clean.. hey ho removed the hex front cover & started having a go at it with Wb's little kit.. There was some pretty solid deposits in there it was a right jobby.. jeepers anyone else come across this? I do...
  3. W

    Would this be ok to run a high pressure shower?

    Don't know anything about them. She has heart set on overhead drencher type shower requiring combi/HP set up. Didn't have time to measure pressure but kitchen hot seemed to have very decent oomph when turning it on.
  4. D

    Worcester Danesmoor 15/19 air setting won't go high enough!

    Manual States it should approximately be 9 but 7 is the highest the needle will go to? The screw just jumps at around 7. Any ideas?
  5. W

    Boiler pressure high when heating & hot water is on?

    Hi there, Recently had a query from a customer as below: Boiler has recently been showing high pressure when hot water or centralheating is on, leading to occasional lock outs.” The boiler is a Potterton HE Powermax. Was thinking it may be a blocked primary heat exchanger? Anyone have any...
    • wild nomad
    • Thread
    • boiler heating high hot water pressure water
    • Replies: 11
    • Forum: Boilers
  6. G

    Any emergency plumbers in Stockport Macclesfield Hyde or High Peak areas?

    I am looking for an established emergency plumber. I have an insurance claims related business and deal mainly with escape of water claims resulting from burst pipes. I can add an extra income stream to your business so message me back. Need to be based in SK postcode.
  7. G

    High water pressure saga

    Moved house a while ago and had a few issues with the plumbing. Taps dripped, pipes rattled when cold water switched on, washing machine leaked etc etc. Builder turned up and said pressure seemed a bit high. As I am in Cornwall pressure anywhere I have lived has been good but never to this...
    • Greenwellies555
    • Thread
    • high pressure water
    • Replies: 3
    • Forum: Bathroom Advice
  8. R

    High heat waste run in mapress

    I have to do a 54mm copper waste run due to it carrying high heat grease and water. I don't want to solder due to it having Whiterock walls. Also I think compression would look poor so was going to go the mapress route. A system I've never used before. My main question is, what's the max...
  9. J

    new thread re high pressure on vaillant eco plus boiler 824r1

    Thread restarted as I have now registered...advice please on below...... ** I have the above boiler - the pressure bar is in the red but I can't find anywhere in the manual which shows how to lower the water pressure - Does anyone know please? Thank you ** The easiest way Is to bleed the...
    • Jmb01
    • Thread
    • boiler high plus pressure vaillant
    • Replies: 1
    • Forum: Boilers
  10. U

    vaillant ecotec plus 824r1 high pressure advice

    I have the above boiler - the pressure bar is in the red but I can't find anywhere in the manual which shows how to lower the water pressure - Does anyone know please? Thank you
  11. B

    High volume water heating

    Can someone please tell me, what would be the cheapest method of heating 36oC water to 45oC at the rate of 80 Litres per minute for 15 minutes and then maintaining this temperature for an hour? All to be repeated every hour. I will have multiple 1200 Litre baths that will fill within 15 minutes...
    • bcraig
    • Thread
    • heating high water
    • Replies: 50
    • Forum: Bathroom Advice
  12. Leo21

    High efficiency pumps and programmers, beware.

    Today i fitted a new lifestyle 112 on a gravity system, and I couldn't stop power going to the pump. Rang lifestyle, and the draw from the pump fuses the programmer into constant power to the pump. A resistors required! I fitted the pump three months ago, oh joy.
  13. R

    High flush wc - siphon & inlet valve

    Hi Friends How long would it take you to change both the above? Cheers
  14. T

    high level WC downpipe

    Hi, I have a situation whereby the cistern of a close coupled WC won't sit on the wall where I'd like it to go, so I'm looking for an alternative solution. The wall in question was originally an external wall and so the end of a nice thick slate window sill (which I don't want to damage)...
  15. E

    Worcester 440 high flow

    My mate got problems getting hot water , only got heating , I took off the divertor motor , noticed pin was out with power off he started getting hot water but no heating , I changed motor (£100) part only . plugged it all back , still no good any ideas ,
  16. M

    high CO reading on worcester 28i rsf boiler

    hi there, mahogany new member to this site. getting high CO reading on Worcester 28i rsf Gc no 47 311 54 burner pressures ok gas rate fine removed burner,removed heat exchanger removed and washed through fins ,took out fan, checked flue all ok.spoke to Worcester technical who said it must be...
    • mahogany
    • Thread
    • boiler high worcester
    • Replies: 4
    • Forum: Boilers
  17. G

    High oil usage

    Hi, We've just had an extension built and a new oil boiler installed (Greenstar 25/32 CF /RS). The original oil boiler was a worcester bosch that was at least 15- 20 years old. It used about 1500 litres oil per year. The new boiler used 1000 litres in its first 3 months and it looks like...
    • Geek
    • Thread
    • high
    • Replies: 24
    • Forum: Boilers
  18. F

    High Flow rate pressure reducer valve

    Hi, I have my presure reducer valve in my kitchen set to 3.5 bar and from that I am geting a flow rate of around 12l per min. I have read on the internet that I should be getting a far higher flow rate from 3.5 bar of presure. Can you let me know what you think? Do you think the presure...
  19. F

    Condensation coming from flue, high ratios, new install

    Just installed an ideal logic I-mini and condensation seems to be coming from the flue, also the ratios it's giving off are high 0009. I've checked the boiler (heat exchanger, condensate trap) but to no avail. I was thinking it could be the gas valve. Any suggestions? Thanks
Back
Top