high | Page 9

Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

high

  1. U

    High level cistern problem

    The wife in her infinite wisdom has decided she wants a high level cistern. As the standard height is 2.3 ish metres and the room is 1.9 my question is can the flush pie be trimmed this much without affecting the flush too much? The cistern is a 3/6 L dual flush. Cheers
  2. S

    Waterfall Tap - Pressure way too high!

    Hi All, I have installed a small waterfall basin mixer tap and the water shoots out horizontally when the taps is on full - in any position (hot, cold mixed). I'm wondering if the tap is knackered or just no good for systems where the pressure is high. If it is the latter then I would say...
  3. U

    Very high cold water pressure and very low hot water pressure!!

    Hi everyone, ive just moved into a place and the cold water pressure both upstairs and downstairs is immense to the point where the pipes bang and the hot water pressure upstairs is virtually non existent but fine downstairs. My question is, can I buy a pump to increase the pressure of the hot...
  4. C

    Good tap for high pressure water - bathroom sinks, bath and kitchen sink!

    Hi, we have really good water pressure where we live. But that in turn has left us with very noisy taps in the bathrooms. At the moment we have Blade taps from the Bathstore - Blade Basin Mono Mini Mixer | bathstore. They have aerators but our water certainly isn't aerated. The taps are...
  5. B

    vaillant ecotec pro 24 high co levels

    hi guys been to service a vaillant today in an empty house, co2 levels fine in the 9's co and ppm were sky high, co over 3000 ive checked over flue (onlyhozontal), seal ect seem fine, can it be a prob with gas valve?? it pretty much blew my fga up, as after it wouldnt register co at all. left it...
  6. R

    Water usage very high when went on holidays

    Hi guys I am Rob and new on this forum, hope someone can shed some light on my very strange issue. Thanks in advance to all the replies. I seem to us around 6 to 7 cubic meters per month. But in October that doubled to nearly 16 cubic meters. The funny thing is I went on holidays from the...
  7. G

    baxi duo tec very high emissions

    hi guys. got call to above boiler today for routine service. as soon as started to analyse it the readings were off the scale was going up to 5000 pm before removing my analyser. i checked for flue integrity and was getting over 600 pm. gas inlet pressure at full rate was 19mbar. its a vertical...
  8. E

    Pressure drops rapidly when off, rising high when on Glowworm combi

    Hello everyone, Hopefully you could share your knowledge on this problem or any advice would be appreciated: The pressure started to drop gradually over the past 2 weeks, but now drops from 1.5bar to 0.3 in 5-8hrs. So I fill up (fillng loop) to 1.5bar to switch on the central heating and the...
  9. F

    how to check flue integrity on halstead high ace

    Servicing the boiler, want to know how to check CO readings, Ratio etc it it says in the manual you can via a plastic cap somewhere, it's an oldish boiler. thanks
  10. K

    Thermostat on high rads turnt low

    Hi we have recently had our outhouse converted and we have 2 new radiators and a towel rad out there, It still gets pretty cold out there even though its all insulated now, i was wondering if i could turn my thermostat right up and adjust my radiators in the main house to a low setting, so the...
  11. B

    High pressure BUT very little water coming out of tap/shower?

    Hi, having some problems with our boiler/shower etc- any advice very, very gratefully received! Basically the pressure dropped to about 0.4 bar the other day so the shower stopped working- we put the pressure back up to 1.5 and it worked fine for a couple of days no problem. but for the last...
  12. M

    Having to run the boiler at high setting 6

    I have a heat only 's' plan system with a Bosch Worcester greenstar 24i on a twin coil Oso solarcyl 200 lt. The boiler has to run at max to heat the water but this means the rads are too hot and I would like to lower the boiler stat. I realise the hot water temperature will only obtain the the...
  13. S

    Heatline vizo 24, Help!! Pressure too high

    The boiler was working fine until recently the pressure gauge shoots up to 4Bar (max) within 15 seconds of switching on the boiler and water starts leaking from the back of the boiler, I bled the radiators and the pressure dropped down to 0.2 and crept up very very slowly to 2.5. My initial...
  14. J

    baxi duotec combi 24he boiler, loud high pitched humming, whining noise.

    Hello I have an 8yo old baxi duotec combi 24he boiler. When the gas central heating is running, it makes a constant loud high pitched humming/whinning noise. The noise only quietens for about 5 seconds, each time the boiler reignites to heat the radiator water. Before then returning to the same...
  15. O

    The man in the high castle

    Does somebody watch this dope season ? i could find only the first 3 but want to carry on watching all the rest just can't find any sort of links for the next one " relevation" ... its pretty nice episode
  16. F

    High flow Combi experiences!

    Hi All, have got a customer with a 5 bed house (two bathrooms and a shower). They want to replace and open vented Y plan system and ideally want to lose the cylinder as they're very tight for space believe it or not. Thinking of quoting to put a Worcester highflow combi in and a booster tank on...
  17. D

    Ford transit connect lwb high top bulkhead cage

    Bulkhead Cage for sale in good condition. £40 essex
  18. S

    Baxi 105e High CO

    Hi all. Today I have done my first boiler service on my own and have come into a bit of a problem. The boiler is a baxi 105e ; the working pressure and burner pressure andgas rate were spot on, and the o2 at the intake, but when I tested the extract, the FGA warned of high CO, the level kept...
  19. S

    Glow worm 18hxi overheating high limit cuts in but display reads 35o

    High limit cuts in with f5 but display reads 35oC Replaced flow/return thermistors but still the same flow temp gets to about 87oC Differentials about 9oC on hot water Any ideas?
  20. T

    Ufch off thermal store, flow temperatures too high??!

    Hi guys, any advice for my situation Ov thermal store with ufch tappings but ufch manifold v close to store, Problem is store temp at 72/73'c Manifold has phial type trv and is shutting down v quickly due to flow temperatures Clearly don't want 72 going through ufch (45ish ideally)...
Back
Top