Good afternoon folks. I wonder if any of you can offer some advice....
I have a hot water cylinder with a pressure reducing valve on top. Yesterday morning it let go in spectacular fashion flooding my downstairs. Having got a local engineer out who i believe seems to know his stuff and...
monkeymanal
Thread
cylinder
hot water
pressure
valve
waterwatercylinder
Hi,
I have copper hot water cylinder in the loft wrapped with a puffa jacket. Its a very old fashion type of copper cylinder where you can simply lift the top off. I've noticed the cylinder has been leaking lately as water has leaked through the ceiling.
When I've been in the loft to inspect...
I'm thinking about installing one of these but I've never come across them so can u tell me how they are vented.
are they any good or do they have any common traits.
Thanks
Ian
Hi All
I have underfloor heating system with rads upstairs run off a 210 L Energy Master2 Cylinder
The system was designed by Nu- Heat and was installed as per spec
The system has run for 3-4 years and has been most effective
However I think the cylinder is leaking I noticed a small plastic...
Hi
With a Worcester Bosch system boiler (its new just 4 years old and a Greenstar 30CDi ) what is the best set up to have it with an unvented hot water cylinder or a vented hot water cylinder (which is what we have at present) ?
Because we are having problems with the air getting into the...
loziv
Thread
boiler
bosch
cylinder
hot water
system
unvented
waterwatercylinder
worcester
worcester bosch
Hi My friend has just moved into a 1960's flat which has electric wall heating and no gas. The hot water cylinder has stumped me. It has a cold feed but also has the hot and cold water coming from it . Well cold anyway,that is the problem there is no water coming out the hot water tap. All...
Robroyx11
Thread
cylinder
electric
hot water
immersion
waterwatercylinder
Being a bank clerk, I am not too conversant with heating matters, but have a question which I hope is OK to ask.
May I paint a picture before asking the question? I would attach a system diagram, but that feature is not enabled at my level of registration on this forum.
I have a hot water...
Hi forum
i need some expert help regarding the replacement of my exsisting hot water cylinder. I currently have a taxi Bermuda back boiler running a gravity fed central heating system with a indirect hot cylinder.
the problem i have is the hot water cylinder has sprung a leak so it requires...
antonio
Thread
central
central heating
cylinder
heating
hot water
replacement
waterwatercylinder
Hi, I've just recently moved home and lookingfor some general advice please from any experts out there. We have a HeatraeSadia CL210 Megaflo unvented hot water cylinder in the airing cupboard. The pressure forthe taps and showers is absolutely great but we've just started having centralheating...
bigbaddomy
Thread
boiler
cylinder
hot water
unvented
waterwatercylinder
I have only ever installed these, so havn't got much fault finding experience. The water pressure out of the hot taps was low, the pressure in the vessel was low so I pumped it up to 3.5 bar, turned the hot water tap on pressure was ok for 30 seconds then it droped, water then came out the prv...
I am just about to replace my ageing indirect open vent hot water cylinder.
The flow for the indirect coil on the new tank is quite a bit higher than on the old tank. The current set up has the 3 way valve at exactly the same level as the flow on the old tank........if I install the new tank...
Hi there,
I need to give an estimate on replacing a hot water cylinder. However, it is connected to an Oil fed boiler and I don't have a qualification to to work on oil boilers. Can I still work on the hot water cylinder connected to it?
Thanks in advance :-)
wild nomad
Thread
boiler
cylinder
hot water
oil boiler
waterwatercylinder
hi i am a apprentice plumber and i am on a trial run with a gas registered plumber and we will be replacing a hot water cylinder with a combi boiler and i wanted to know how this is done so i have some knowledge for when we do the job on Monday. can anyone help?????
lukev1
Thread
combi
cylinder
hot water
replace
waterwatercylinder
Planning to install an unvented water cylinder to supply 5 showers in a club. Potentially up to 25 people using the showers after matches, in turn obviously. 5 electric showers was my first thought because there's no chance of the water running out but presumably more expensive to run and the...
Hello would appreciate some fedback on this please , I have a y plan sytem in place , a 115litre hot water tank heated
indirect via boiler , no immersion heater fitted ( could not remove cap , did bot want to risk damage to tank)
ok and i have an abundance of electricity coming form my solar...
After some advice please. Just installed a new indirect vented copper cylinder and I've got a small weep from the cold water in Male iron 22mm x 1. I use plumbers tape wrapping the threads approximately 10 times.
I've just ordered a 1inch fibre washer, will the washer help and should I apply a...
Hello everyone,
I have a megaflo hot water cylinder which is dripping from the tundish. Have had two weeks ago a gas safe registered engineer to service my boiler and my hot water tank and he said the hot water cylinder would just need the air gap replenished (which he supposedly did)...
Hi there,
I need to replace a washer on the mixer tap in our kitchen. Would be much appreciated if I could get some advice on the correct way to turn the water off / on. I live in a 3 storey townhouse, the kitchen is on the 1st floor and the Hot Water Cylinder is in the airing cupboard on the...
I am looking for a way to keep a tank of fluid at an reasonably constant temperature.
How accurate are the hot water cylinder thermostats?
I'm thinking of wiring two up to to control a narrow heating range.
The field I'm heating needs to be at around 96c but if it goes over 100c it will...
Hi all,
My bathroom radiator is heated via the hot water cylinder - I'm not sure if this is just to heat towels when Heating is off or its for a requirement for the cylinder?
Any ideas?
Reason I ask is because I am removing the wall between the bathroom and toilet to make it all one room...
clintpike
Thread
bathroom
cylinder
hot water
radiator
waterwatercylinder