What we all working on this week ?

[king of pipes]

I have a insurance job to try and rescue a poorly installed quad shower the customer wants to save the tiling if possible and has a few spare so fingers crossed it may work , the loss adjuster allowed em £1500 that will just about cover materials. Kop

 

[ShaunCorbs]

Blank canvas now chaps took some Sh-te out of this one now got to put it back together ,🙄🙄
Cheers kop

did you skim it kop ?

 

[king of pipes]

did you skim it kop ?

No mate did the boarding and prep got a mate who did it for me.

 

[Harvest Fields]

Was just going to ask the same question.
[automerge]1579810660[/automerge]
Standard board or Hardi/waterproofed

 

[king of pipes]

Moisture resistant where there is shower boards going 12.5mm standard board else where , hardi going on the floor then tiling it , tiled skirting , shower bath new shower, new toilet basin & pedestal towel rail ect .

 

[Stigster]

We're running an unvented certification (G3) course today. I'm doing the practical side of it. I've got a shocker of an install setup and they've got to come and inspect it, decide what's non-compliant and come up with solutions.

I'll do a little bit on common faults and also a recap on servicing procedures whilst they are here too.

A nice way to end the week. I really do enjoy helping to run this particular session! There's even a chance we might have an early finish. I've got a new drone and I'm itching to get out on the coast and give it a fly whilst the air is so calm here at the moment. 13 mph winds, well within the craft's capabilities and safety limits. A half past three finish will allow me to get out there for a fly before we lose the light.

 

[ShaunCorbs]

We're running an unvented certification (G3) course today. I'm doing the practical side of it. I've got a shocker of an install setup and they've got to come and inspect it, decide what's non-compliant and come up with solutions.

I'll do a little bit on common faults and also a recap on servicing procedures whilst they are here too.

A nice way to end the week. I really do enjoy helping to run this particular session! There's even a chance we might have an early finish. I've got a new drone and I'm itching to get out on the coast and give it a fly whilst the air is so calm here at the moment. 13 mph winds, well within the craft's capabilities and safety limits. A half past three finish will allow me to get out there for a fly before we lose the light.

what model stig dji?

 

[Stigster]

Yes, a DJI Mavic Mini. This week I've just been doing some indoor flight and getting the hang of it all.

Check out the reviews as this little beauty is surprisingly capable despite it's 249 gram weight. A weight also designed to keep it from needing CAA registration or public liability insurance, in my jurisdiction at least. That said for peace of mind I have joined the British Model Flying Association and taken out 25 million quids worth of public liability on it.

I think it's best to go above and beyond the basic requirements for things like this. I've also memorised all the laws and regulations relating to where I can and cannot fly, height restrictions, airport proximity and all that important stuff.

 

[Harvest Fields]

Anyone else working today? Don’t normally work weekends but had to work the last 3

 

[centralheatking]

Anyone else working today? Don’t normally work weekends but had to work the last 3

I was on phone to Iraq at 4am this morning been a bit chaotic since Trump took out the Iranian fella
In Baghdad ...but its all back on line now. We are supplying materials for the rebuilding of Iraq, smart quick assembly roof system ....centralheatking

 

[king of pipes]

Only a site meeting with other trades for me and a small repair job then done . Kop
[automerge]1579970181[/automerge]

Anyone else working today? Don’t normally work weekends but had to work the last 3

That's ya holiday paid for H ,

Anyone else working today? Don’t normally work weekends but had to work the last 3

 

[Harvest Fields]

Wish it was mate. They cost a fortune.

 

[ShaunCorbs]

Stripping out a fancy bathroom or two

 

[king of pipes]

Stripping out a fancy bathroom or two

Doing up your own place Shaun

 

[Stigster]

Mmmm bathroom carpets...

 

[ShaunCorbs]

Doing up your own place Shaun

i wish trying to cobble together an old manor house, converted 20 years ago into two then back into one big family house now back into two so you can guess the amount of redundant pipework there is

4 unvented cylinders

2 300ls for the main houses and 2 150l in series for some reason serving one bathroom
[automerge]1580163976[/automerge]

Mmmm bathroom carpets...

all coming up he wants tile with ufh

 

[king of pipes]

You're gonna be a busy boy post some pictures up as you go bud looks like a top end job .
Cheers kop

 

[king of pipes]

This one is coming on now still a bit to do though . Kop

 

[SimonG]

Can you knock me up a towel rail. Ooooh lovely.

Not my cup of tea but what do I know!

 

[Harvest Fields]

Working on this. This week and next Cubicle absolutely rotten

 

[SimonG]

Little basin change this morning and then change a low pressure sensor on a crappy grant boiler later.

 

[ShaunCorbs]

Finishing stripping out and draining down 4 rads only problem was had to drain the entire system total was around 55-60 rads

 

[Harvest Fields]

Wish my day was as simple. The floor is rotten on my job as well, (sheet boarding). Always the way when you could do with the job going smoothly. Is that Hardi on the floor shaun?

 

[SimonG]

Didn't turn out too bad. Customer just needs to touch up the emulsion.

 

[Harvest Fields]

Didn't turn out too bad. Customer just needs to touch up the emulsion.

That basin and unit looks familiar? City plumbing?

 

[ShaunCorbs]

Wish my day was as simple. The floor is rotten on my job as well, (sheet boarding). Always the way when you could do with the job going smoothly. Is that Hardi on the floor shaun?

yes mate but not installed correctly for my liking (tilers installed it)

should be glued to the floor with either mi approved foam or tile addy

its all plastic so install isnt the best

would love something to get my teeth in atm but flip side back to site tomorrow so should be happy